00197295-01_UM_D4i_SR605_EN.pdf - 第218页
6 Station extensions User manual SIPLACE D4i 6.1 Nozzle changer for the 12-nozzle Collect & Place head From software version SR.605.03 SP2 10/2012 EN edition 218 6.1.4 Assembly Each nozzle changer (see Fig. 6.1 - 2 )…
User manual SIPLACE D4i 6 Station extensions
From software version SR.605.03 SP2 10/2012 EN edition 6.1 Nozzle changer for the 12-nozzle Collect&Place head
217
6.1.3 Position of the nozzle changers for the C&P12 head
At locations 1 to 4, two nozzle changers can be installed at each location for the 12-nozzle
Collect&Place head (item 1 and 6 in Fig. 6.1 - 2
). This gives a total capacity of 8 nozzle changers
with 40 magazines and 480 nozzle holders.
6
Fig. 6.1 - 2 Position of the nozzle changers for the 12-nozzle Collect&Place head
6
(1) Nozzle changer
(2) Nozzle magazine
(3) Reject bin for nozzles
(4) Take-off device for nozzles
(5) Reject bin for components
(6) Installation location for a second nozzle changer
6 Station extensions User manual SIPLACE D4i
6.1 Nozzle changer for the 12-nozzle Collect&Place head From software version SR.605.03 SP2 10/2012 EN edition
218
6.1.4 Assembly
Each nozzle changer (see Fig. 6.1 - 2) is fixed to the used tape channel.
6
Fig. 6.1 - 3 Assembly position
(1) Spring hook pointing toward the operator
(2) Retaining clamp pointing toward the PCB conveyor
→ Align the nozzle changer so that the moving spring hooks always point toward the operator,
while the retaining clamps always point toward the PCB conveyor.
6.1.5 Notes on operation
→ When you fill a magazine with a certain nozzle type for the first time, attach an adhesive label
to identify the type.
PLEASE NOTE 6
Fill the magazines off the machine and always replace complete magazines. 6
→ Open the locking plate and place the nozzles in the nozzle holders.
→ Close the locking plate so that the nozzles cannot drop out of the magazines.
User manual SIPLACE D4i 6 Station extensions
From software version SR.605.03 SP2 10/2012 EN edition 6.1 Nozzle changer for the 12-nozzle Collect&Place head
219
CAUTION 6
Before you fill magazine, make sure that all the nozzles on the Collect&Place head have
been returned to their magazines. 6
→ Programming the nozzle changer is described in the SIPLACE Pro user manual.
PLEASE NOTE 6
→ Do not allow components to drop onto the magazines. If they do, they could jam the locking
plate.
→ Do not allow components to drop onto free feeder module locations. They will stick to the mag-
netic bar. Production may have to be interrupted if the feeder modules are not placed on the
component table correctly. You should therefore regularly clean the magazines and free loca-
tions.
6.1.6 Changing the magazine
→ To remove the magazine, push the spring hook (item 1 in Fig. 6.1 - 4, page 220) away from
the magazine. Lift the magazine out of the carrier.
PLEASE NOTE
Make sure that you insert the magazine so that the centering pins slide into the centering hole
(item 3 in Fig. 6.1 - 4, page 220) and slot (item 4 in Fig. 6.1 - 4, page 220). 6
→ First place the side of the magazine with the numbered nozzles 1, 2, 3 and 4 on the base.
The retaining clamp (item 2 in Fig. 6.1 - 4
, page 220) must slide into the slot in the magazine.
→ Push the spring hook away from the magazine (item 1 in Fig. 6.1 - 4
, page 220).
→ Press the magazine so that it lies flat on the base, then release the spring hook. The spring
hook must latch into place.