User Manual SIPLACE Head Care Station -.pdf - 第8页
1 Introduction 1.1 Overview 8 User Manual SIPLACE Head Care Station 10/2017 Types of measurements Head verification includes a number of measurement steps which can be executed individually or as a whole sequence. These …
1 Introduction
1.1 Overview
User Manual SIPLACE Head Care Station 10/2017 7
1 Introduction
This user manual provides information on the installation and operation of the SI-
PLACE
®
HeadCareStation(HCS).
1.1 Overview
Fig.1: HCS complete
1 Monitor 2 Control box HCS 2.3 [03149138-xx]
3 HCS 2.3 head unit CPx+TH
[03149140-xx]
4 Keyboard
5 Mouse
NOTICE
Monitor, keyboard and mouse are not included in the scope of delivery.
1.1.1 Description
The HeadCareStation(HCS) is a service tool to verify the functional setup of SIPLACE placement
heads outside the machine.
The following placement heads can be verified:
C&P20, C&P20A, C&P20M, C&P20P, C&P20M2, CPP, CPPM, TH (Pick&Place module)
For more information, see 1.4.6 "Abbreviations" [}12].
1 Introduction
1.1 Overview
8 User Manual SIPLACE Head Care Station 10/2017
Types of measurements
Head verification includes a number of measurement steps which can be executed individually or
as a whole sequence. These measurement steps vary depending on the head to be verified. The
following checks are performed on the sub-units of the placement heads:
●
State of the vacuum system and corresponding
●
Ease of movement of DP and Z-axis bearings
●
Wear on bearings / tolerances
●
Component sensor check
●
Z-axis light barrier check
●
Positioning accuracy of DP drives
●
Nozzle seat check
●
Vacuum system verification
●
Placement force verification
At the end of the verification process, all results are summarized in a test report which can also be
saved to a PDF file. These results provide feedback about the technical state of the head, enabling
a technician to decide which measures are to be taken, for example:
●
Performing additional maintenance
●
Replacement of wear/spare parts
Replacement of the head
1.1.2 Serial number
The serial number of the HCS can be found on the type plate of the control unit (bottom side) or on
the head unit (right side). 3.1.1 "HCS 2.3 Head Unit CPx + TH [03149140-xx]" [}31]
1.1.3 EU Declaration of Conformity
The product/device described below conforms to the regulations and standards specified in the
EUDeclaration of Conformity.
Type: Testing and verification device
Product: Head Care Station
Unit: HCS head unit CPx + TH
Item no.: 03149140-01
Manufactured by: ASM Assembly Systems GmbH&Co.KG
Rupert-Mayer-Str. 44
81379 Munich
Germany
Product: Head Care Station
Unit: Control box HCS
Item no.: 03149138-01
Manufactured by: ASM Assembly Systems GmbH&Co.KG
Rupert-Mayer-Str. 44
81379 Munich
Germany
1 Introduction
1.1 Overview
User Manual SIPLACE Head Care Station 10/2017 9
1.1.4 Use as prescribed
The product may only be used for the areas of application specified in the catalogues and technical
descriptions, i.e. for testing and verifying SIPLACE placement heads, and may only be used to-
gether with the third party devices and components recommended or approved by ASMAssembly
SystemsGmbH&Co.KG. Use for a different or extended purpose is not prescribed.
In the case of incorrect usage, ASMAssembly SystemsGmbH&Co.KG will not assume liability
for any damage which occurs and will not guarantee the correct and proper function of machine
components.
Use as prescribed also includes compliance with all the instructions in the user manual.
For the product to operate correctly and reliably, it must have been transported, stored, erected
and assembled correctly and must be operated and maintained with care.
1.1.5 Failure to use as prescribed
Failure to use the product as prescribed can result in both danger to life and limb and material
damage. For this reason, use other than as prescribed is expressly prohibited. In the case of
incorrect usage, ASMAssemblySystemsGmbH&Co.KG will not assume liability for any damage
which occurs and will not guarantee the correct and proper function of HCS components.
Use of the HCS other than as prescribed includes, for example:
●
Use of the HCS by unqualified personnel.
●
Operation of the HCS with safety equipment deactivated or removed.
●
Testing of heads that do not meet the permitted specification.
●
Use of tools that have not been approved.
●
Use of unauthorized accessories and additional tools.
1.1.6 Noise emissions
Max. noise emissions 75 dB (A)
1.1.7 Important notes on environmentally-friendly disposal of materials and
components
SIPLACE machines are preferably manufactured using materials and parts that can be easily sep-
arated and disposed of in an environmentally-friendly way.
NOTICE
Correct and environmentally-friendly disposal by the operator
The owner of the system has sole responsibility for the proper environmentally-
friendly disposal of machines, working materials, consumables and wear parts.
► Please observe your national statutory provisions for waste disposal and environ-
mental protection.
1.1.8 Electromagnetic compatibility (EMC)
ASM Head Care Stations are designed and tested for professional use in industrial applications.
Electromagnetic compatibility in terms of the emission of interference cannot be guaranteed in any
other environment.
1.1.9 Note on original SIPLACE accessories
NOTICE
Use of original spare parts and authorized accessories
The use of other parts will affect safety and will invalidate the liability for any consequential
damage.
► Only use original spare parts and authorized accessories from ASMAssemblySys-
tems GmbH&Co.KG.