00195044-22_UM_VisionTeachStation_5.x.x_DE_EN.pdf - 第153页
Vision Teach Station 5.x.x User Manual 8 Starting the vision teach station 05/2019 Edition 8.1 Switching on the vision teach station 61 8 Starting the vision teach station Check the power cable co nnections before you sw…
7 Software Vision Teach Station 5.x.x User Manual
7.4 Error report 05/2019 Edition
60
7.4 Error report
7.4.1 SIPLACE Vision Station
The "BugReporter" is provided on the following path for reporting errors that occur while the
SIPLACE vision teach station is in use to SIPLACE Service:
<Install path for SIPLACE Vision Teach Station>\BugReporter.exe 7
Alternatively, you can also run the BugReporter from the Start menu -> Programs -> TeachStation.
This allows you to save information about the SIPLACE vision teach station in a compressed file
(Zip file) and to send it to the Service for investigation, if necessary.
7.4.2 SIPLACE Pro
Errors that occur in association with SIPLACE Pro can be reported via the ASM Error Reporter
Service. This is started from Start – Programs – ASM Net – Enterprise Service – ASM Error
Reporter Service.
Vision Teach Station 5.x.x User Manual 8 Starting the vision teach station
05/2019 Edition 8.1 Switching on the vision teach station
61
8 Starting the vision teach station
Check the power cable connections before you switch on the vision teach station.
– Base module and PC see section 4
, from page 25.
– Cameras see section 5
, from page 29.
WARNING 8
NEVER remove the 26-pin ribbon cable from the Collect&Place head camera while the base
module is switched on as this could damage the LED driver board for the camera.
8.1 Switching on the vision teach station
Switch the base module on at the power switch.
The three LEDs on the back of the base module light up.
Switch the PC on and log in as Administrator (see section 7.2, page 54) or as a user.
8.2 Starting the vision teach station application
Double-click on the "Teach Station" icon to start the application. The application will detect any
cameras that are connected. The live image of the first camera is displayed on the application's
starting screen. If there are two cameras connected, you can toggle between the two.
8 Starting the vision teach station Vision Teach Station 5.x.x User Manual
8.3 Error messages when starting the application 05/2019 Edition
62
8.3 Error messages when starting the application
The following error messages may appear when you start the application:
8.3.1 No camera was detected
Check that the base module is switched on and that all 3 LEDs light up.
If the three LEDs light up, then the + 24 V- (red), + 15 V- (yellow) and + 42 V- (green) supply
voltages are present (see section 4.2
, page 26). 8
If one of the LEDs does not light up, contact SIPLACE Service. 8
If all 3 LEDs do not light up, check the 2.5 A fuse (item 1 in Fig. 8
4.2 - 1
, page 26). 8
Check whether the CAN bus cable between the PC and the base module or between the base
module and the stationary camera is connected correctly.
Exit and restart the vision teach station application.
8.3.2 Camera not responding
If a stationary camera is concerned (type 33/type 25):
Check that the orange camera bus cable is connected between camera and PC.
If a head camera is concerned:
Check that the orange camera bus cable is connected on the back of the basic module
(connection (5) in Fig. 4.2 - 1
, page 26) and to the PC.
Check whether there are bent connection pins on the plugs of the "adapter for head camera"
(Fig. 5.2 - 9
, Seite 41) .
If the camera still is not detected, contact SIPLACE Service.
8.3.3 There is a vision teach station application running already
Exit the application and then start it again.
8.3.4 Error: LED self-test failed. Not all LEDs are working properly
One or more LEDs for the camera illumination has failed.
Replace the defective camera.