TRS GEM Manual for Intel Ver 1.1.pdf - 第104页

GEM Manual for DEK P rinters Equipment Variables Issue 1.1 March 20th, 2014 Page 104 of 152 Page 104 of 152 RunGEMRem ote 41 Allow s control of the Run With GEM Remote parameter. When enabled, only the host can start the…

100%1 / 152
GEM Manual for DEK Printers Equipment Variables
Issue 1.1 March 20th, 2014 Page 103 of 152 Page 103 of 152
7.2 Equipment Constants
The equipment constants are defined in the table below:
Note: Default values are shown bold.
NAME
ECID
DESCRIPTION
Type
Value Range
GemConfigConnect
1
Select establish communications type.
U1
1 = S1F13
DeviceName
2
Equipment name as defined by the host.
A20
20 characters
GemEstabCommDelay
3
Time between each S1F13 poll.
U2
0-60-1800 s
GemPollDelay
4
Time between each S1F1 poll.
U2
0-60-1800 s
GemInitCommState
5
Initial communications state.
U1
1 = Enable
0 = Disable
GemInitControlState
6
Initial control state.
U1
1 = OFF-LINE
2 = ON-LINE
GemOfflineSubstate
7
Set default control sub-state when equipment is
OFF-LINE.
U1
1 = Equipment Off-Line
2 = Attempt On-Line
3 = Host Off-Line
GemOnlineFailed
8
Default sub-state following ON-LINE failure.
U1
1 = Equipment Off-Line
2 = Host Off-Line
GemOnlineSubstate
9
Default sub-state when entering ON-LINE state.
U1
4 = Local
5 = Remote
received_mode
10
Set System Mode. This constant is volatile and
defaults to Auto on machine power up.
U1
1 = Auto
3 = Pass Through
InspectRate
11
Number of print cycles between board
inspections. 0 indicates no inspection
F8
0 – 100
BatchLimit
12
Number of boards to be printed in a production
batch. O indicates no batch limit
U4
0 - 99999
process_adjustments
13
Enables/disables adjustment of the current
printing process while the machine is running.
U1
0 = Enabled
1 = Operator disabled
2 = Remote command
disabled
3 = Both disabled
MaxSpoolTransmit
14
The maximum number of messages that the
equipment will transmit from the spool in
response to a S6F23”Transmit spooled
Messages” request. If MaxSpoolTransmit is set
to zero, no limit is placed on the messages sent
from the spool. Multi-block inquire/grant
messages are not counted in this total.
U4
Minimum = 0
Maximum = value of
SpoolCountActual
OverWriteSpool
15
Tells the printer to overwrite data in the spool
area or stop spooling whenever the spool area
limits are exceeded.
B1
1 = TRUE to overwrite
spooled data
0 = FALSE to stop
spooling when limits are
exceeded.
spooling_enabled
16
Allows the equipment to default to a condition
where spooling is disabled completely. This is
provided for older Hosts that do not support
S6F23. This EC is set to TRUE = 1 on receipt of
S2F43 defining messages to be spooled.
B1
0 = FALSE spooling
disabled
If the Host sets this EC to
FALSE any data in the
spool will be purged.
Reserved
17-39
Not used by the 265.
TimeFormat
40
The setting of this ECV controls whether the
equipment shall send the Data Items STIME and
TIME in 12-byte or 16-byte format. It also
controls the format of START_TIME. to be 6 or
7 bytes.
B1
0 = 12 byte format
1 = 16 byte format
>1 reserved
GEM Manual for DEK Printers Equipment Variables
Issue 1.1 March 20th, 2014 Page 104 of 152 Page 104 of 152
RunGEMRemote
41
Allows control of the Run With GEM Remote
parameter. When enabled, only the host can
start the printer and the operator is given an
appropriate message.
U1
0 = Disable
1 = Enable
CompoundProductFiles
46
Controls whether Compound Product
functionality is enabled or disabled.
U1
0 = Disable
1 = Enable
Make
50
Printer make. Always returns “DEK”
A20
“DEK”
Model
51
The model of the printer
A20
For example “Galaxy”
StencilCleaningSystem
53
The currently selected cleaner module
U1
0 = None
1 = Blue
2 = Vortex
3 = Cyclone
ApplicatorType
54
The currently selected applicator module
U1
0 = Squeegees
1 = ProFlow (classic)
2 = Ball Placement
3 = ProFlow Tx
4 = ProFlow ATx
ConveyorType
55
The fitted conveyor type
U1
0 = Standard
1 = HTC
2 = RTC
TransportMode
56
The current rail transport mode
U1
0=LeftToRight
1=RightToLeft
2=RightToRight
3=LeftToLeft
4=NoTransfer/Shuttle
MachineUnits
57
The current machine units
U1
0=Metric
1=Imperial
UplineProtocol
58
The current up-line FMI protocol
U1
0=NoFMI
1=MIU
2=Manual
DownlineProtocol
59
The current downline FMI protocol
U1
0=NoFMI
1=MIU
2=Manual
TransferPeriod
60
FMI transfer period (s)
U2
0 – 999, 20
PasteDispensePosition
61
The position the paste dispenser uses
U1
0=Front
1=Rear
2=Auto
ToolingHardware
62
The currently selected tooling type
U1
0=Magnetic
2=Vacuum
6=FormFlex
7=GridLok
FiducialReference
63
The current fiducial reference
U1
0=Left
1=Right
ProductBarcodeHardw
are
64
The status of the product barcode scanner
U1
0=Not Fitted
1=Fitted
RemoteBarcodeHardw
are
65
The status of the remote barcode scanner
U1
0=Not Fitted
1=Fitted
AdvancedProflow
66
Status of the Advanced ProFlow option
U1
0=Disabled
1=Enabled
PressureHardware
67
The currently selected pressure hardware
U1
0=NotFitted
1=Fitted
PasteDispenser
68
The status of the automatic paste dispenser
U1
0=NotFitted
1=Fitted
ScreenSize
69
The current screen type selection
U1
0=256
1=Fuji
2=249
3=Sanyo
4=Library
GEM Manual for DEK Printers Equipment Variables
Issue 1.1 March 20th, 2014 Page 105 of 152 Page 105 of 152
RollHeightHardware
70
The current selection of the Paste Roll Height
Monitor (PRHM) hardware
U1
0=NotFitted
1=Fitted
RollHeightMonitor
72
The current status of the PRHM option
U1
0=Disabled
1=Enabled
ConsumableAction
73
The current setting for the action to perform
when a consumable is low
U1
0=Warn
1=Pause
2=Suspend
VacuumHoldTime
74
The time the vacuum is applied to the tolling
before the quality of the vacuum seal is checked
(s)
F4
2DiMovementTuning
75
The settling time used in 2D Inspection per site
(ms)
U2
CleanerVacuum
76
The current status of the cleaner vacuum option
U1
0=Standard
1=Vacuum
PasteTrails
77
The current status of the paste trails option
U1
0=Disabled
1=Enabled
TransportWaitMode
78
The current setting for the transport wait mode
U1
0=Standard
1=Hold At Print
ClampType
80
The current selection for the board clamp type
U1
0=Board Clamps
1=Snuggers
2=Foil Less Clamps
3=Over The Top
Snuggers
ToolingMonitoring
81
The rate (in boards) that the Tooling Deviation
Monitoring option is used
U2
0 – 200. 0 = disabled
FiducialMonitoring
83
The current selection for the Fiducial
Monitoring option
U1
0=Smart
1=Normal
FiducialSearch
84
The current selection for the Fiducial Search
option
U1
0=Disabled
1=Custom
RemoteBoardStopHard
ware
85
The current selection for the Remote Board Stop
hardware
U1
0=NotFitted
1=Fitted
BoardStopXOffset
86
The current camera board stop X offset
F4
CameraIdlePosition
88
The current selection for the Camera Idle
Position option
U1
0=Home
1=Behind Rail
UnloadBoardStart
89
The current selection for the Unload Board Start
option
U1
0=Transport
1=Separation
MaintenanceMonitorin
g
95
The current state of the Maintenance Monitoring
option
U1
0=Disabled
1=Enabled
MachineLocation
96
Free format entry to describe the location of the
machine
A20
AutoRailWidth
97
The current selection for the Automatic Rail
Width option
U1
0=Disabled
1=Enabled
ProductDirectory
98
The path to the local folder where the product
files are stored
A260
DataFileLocation
99
The path to the local folder where data and log
files are stored
A260
DownlineBoardStop
101
The current selection of the HTC Downline
Board Stop option
U1
0=Never
1=Always
2=Auto
AdjustPageType
102
The current selection for the Adjust page option
U1
0 = Standard
1 = Reduced
Sublimits
103
The current selection of the Adjust Page sub-
limits option
U1
0 = Disabled
1 = Enabled
FrontRToLSpeed
104
The speed of the front rail belt when running
from right to left
U2
FrontLToRSpeed
105
The speed of the front rail belt when running
from left to right
U2