TRS GEM Manual for Intel Ver 1.1.pdf - 第148页

GEM Manual for DEK P rinters Appendix B Issue 1.1 March 20th, 2014 Page 148 of 152 Page 148 of 152 Appendix B Operator instructions for c onfiguring a nd using GEM on DEK printers. 12.1 Netw ork Configuration The GEM I P…

100%1 / 152
GEM Manual for DEK Printers Appendix A
Issue 1.1 March 20th, 2014 Page 147 of 152 Page 147 of 152
Remote Command Parameters:
PP_SELECT Parameters
CPNAME (ASCII)
DESCRIPTION
CPVAL type
min-max
RECEIVED_FILE_NAME
Name of the process program to use.
ASCII
RENAME_PRODUCT Parameters
CPNAME (ASCII)
DESCRIPTION
CPVAL type
min-max
OLD_FILE_NAME
The old name of the process program.
ASCII
NEW_FILE_NAME
The new name of the process program.
ASCII
ADJUST PARAMETER Parameters
CPNAME (ASCII)
S2F21
DESCRIPTION
CPVAL
type
Range
Resol.
ADJUST_PASTE
0
Adjusts paste dispense rate.
F8, none
0-100
1
ADJUST_FRONT_SPEED
1
Adjusts front print speed.
F8, mm/s
2-150
ADJUST_REAR_SPEED
2
Adjusts rear print speed.
F8, mm/s
2-150
ADJUST_FRONT_PRESS
3
Adjusts forward print pressure.
F8, Kg
0-20
0.2
ADJUST_REAR_PRESS
4
Adjusts reverse print pressure.
F8, Kg
0-20
0.2
ADJUST_PROFLOW_PRESS
5
Adjusts Proflow print pressure.
F8, Kg
0-20

ADJUST_GAP
6
Adjusts print gap.
F8, mm
0-6
0.025
ADJUST_SEPARATE
7
Adjusts separation speed.
F8, mm/s
0.1–20
0.1
ADJUST_CLEAN
8
Adjusts clean screen rate.
F8, none


ADJUST_FWD_X
9
Adjusts forward X offset.
F8, mm
1
0.004
ADJUST_FWD_Y
10
Adjusts forward Y offset.
F8, mm
1
0.004
ADJUST_FWD_T
11
Adjusts forward offset.
F8, arcsec
00
2
ADJUST_REV_X
12
Adjusts reverse X offset.
F8, mm
1
0.004
ADJUST_REV_Y
13
Adjusts reverse Y offset.
F8, mm
1
0.004
ADJUST_REV_T
14
Adjusts reverse offset.
F8, arcsec
00
2
CHANGE_SCREEN Parameters
CPNAME =
“CHANGE_METHOD”
DESCRIPTION
CPVAL type
CPVAL = “AUTO”
Exchange the screen in the printer (if present) with one in the
autochanger. Load the new screen to the position specified
by the process program.
ASCII
CPVAL = “MAN_LOAD”
Load the screen in the printer to the position specified by the
process program.
ASCII
GEM Manual for DEK Printers Appendix B
Issue 1.1 March 20th, 2014 Page 148 of 152 Page 148 of 152
Appendix B
Operator instructions for configuring and using GEM on DEK printers.
12.1 Network Configuration
The GEM IP Address for the machine must be set up in the DekSECSII.cfg file, this can be checked
and edited if necessary in the configuration file E:\Config\DekSECSII.cfg.
Set the PASSIVE ENTITY IP ADDRESS to the printer’s IP Address.
The IP Address can be obtained by using the ipconfig command at the command prompt.
If there is more than one printer communicating with the GEM host, set the DEVICEID differently for
each printer. The default value is 0x109 (265). Alternate DEVICEID values should be chosen within
the range 0x0000 – 0x7FFF (0 – 32767).
12.2 Enabling GEM
Classic User Interface
From the Ready page:
1. Select Maintenance (F8)
2. Select Set Prefs (F5)
3. Change the value of Host Comms to GEM
4. Select Enable Comms (F1).
Instinctiv User Interface
From the Ready page:
1. Select Maintenance
2. Select Machine Setup
3. Select Network
4. Change the Comms Protocol to GEM
GEM Manual for DEK Printers Appendix B
Issue 1.1 March 20th, 2014 Page 149 of 152 Page 149 of 152
5. Select Enable Comms
12.3 Using GEM
Once enabled and communicating with a host, the operator can perform the following functions:
1. Switch between online and online state
2. Switch between local and remote state
3. Transfer product files to and from the host
4. Terminal services
Classic User Interface
From the Ready page:
1. Select Monitor (F7)
2. Select Host Comms (F2)
3. To switch to online state, select On-Line (F4). The printer will change to “Attempt On-Line”
state until the host accepts the request.
4. To switch to offline state, select Off-Line (F5)
5. To switch between local and remote modes, select Local/Remote (F6)
6. To transfer a product from the printer to the host, select Transfer To Host (F2):
a. Navigate to the required product using Left, Right, Previous, Next (F4 – F7)
b. Select Upload (F1) to transfer the product
c. Select Exit (F8) to cancel the transfer
7. To transfer a product from the host to the printer, select Transfer To Equipment (F3):
a. Enter the name of the product file
b. Select Download (F1) to transfer the product
c. Select Exit (F8) to cancel the transfer
8. To access terminal services, select Terminal Services (F1):
a. Recent messages from the host will be displayed
b. Type a new message and select Send Message (F1) to send a message to the host
c. Select Exit (F8) when finished
9. To test communications with the host, select Test Comms (F7)
Instinctiv User Interface
From the Ready page:
1. Select Host Comms
2. To switch to the online state, select Online