Nordson_EFD_RV_Series_Operating_Manual.pdf - 第75页
RV Series Automated Dispensing Systems 75 www.nordsonefd.com info@nordsonefd.com +1-401-431-7000 Sales and service of Nordson EFD dispensing systems are available worldwide. How to Use Marks to Dispense onto a Plain W or…
RV Series Automated Dispensing Systems
74 www.nordsonefd.com info@nordsonefd.com +1-401-431-7000 Sales and service of Nordson EFD dispensing systems are available worldwide.
How to Use Marks or Fiducial Marks in a Program
Use the Mark command in a program as follows:
• To confirm the presence or absence of a workpiece.
• To confirm that the correct workpiece is present.
• To check the XY position of a workpiece.
Use two Fiducial Marks in a program as follows:
• To move the dispensing tip to a specific target area on the workpiece.
• To check the XY orientation of a workpiece. The system automatically adjusts the program to compensate for
any changes in orientation.
PREREQUISITES
The system is properly set up. Refer to “Setting Up and Calibrating the System (Required)” on page45.
The system is in the CCD Mode.
#
Click Step
1
• Determine whether you need to create one mark or two and then create the
marks. Refer to “How to Create a Mark” on page72 for the procedure for
creating marks.
2
• Insert a Find Mark command or two Find Fiducial Mark commands near the
beginning of a program.
3
• If the program includes a Step & Repeat command, use the Mark Adjust or
Fiducial Mark Adjust commands.
4 • Refer to the sample program below as a guideline.
RV Series Automated Dispensing Systems
75www.nordsonefd.com info@nordsonefd.com +1-401-431-7000 Sales and service of Nordson EFD dispensing systems are available worldwide.
How to Use Marks to Dispense onto a Plain Workpiece
The Edge Adjust command is needed when you must create a dispense program for a workpiece that presents one
of the following challenges:
• Very large, rounded corners
• No obvious features for creating a mark image
PREREQUISITES
The system is properly set up. Refer to “Setting Up and Calibrating the System (Required)” on page45.
The system is in the CCD Mode.
To learn how to use this feature, draw a black rectangle with very round corners on a sheet of white paper and
use it as a template.
Overview for Dispensing onto Featureless Workpieces
The following tasks are required to create a program for dispensing onto very plain workpieces:
• Creating and saving mark images on two edges of a rectangular area. For each mark, you will need to enter
Width and Height values.
• Setting up the search range for each mark.
• Correctly using the Find Mark and Edge Adjust commands in the dispense program.
Vertical marks 3 and 4
Horizontal marks 1 and 2
1 2
3
4
RV Series Automated Dispensing Systems
76 www.nordsonefd.com info@nordsonefd.com +1-401-431-7000 Sales and service of Nordson EFD dispensing systems are available worldwide.
How to Use Marks to Dispense onto a Plain Workpiece (continued)
To Create Horizontal and Vertical Marks on a Plain Workpiece
# Click Step Reference Image
1
• Click CAMERA to go to the camera
screen.
2
• Bring the image into focus. Refer to
“Camera” on page16 as needed for
instructions on focusing the camera.
3
>
• Click SET MARK, then click and drag a
red rectangle over the first horizontal
target on the workpiece.
• Center the red rectangle on the edge of
the workpiece by clicking and dragging
a corner.
4
>
• Double-click the crosshairs in the center
of the red rectangle and then enter the
desired values for Width and Height (20
and 40 in this example).
• Click OK to save the values.
5
>
• Click a socket in the Mark Library to
save the mark, then click TEMPLATE
when the Template Match window
appears.
• Make a note of the Mark No.
6
>
> >
• Click RANGE to set where the system
searches for the mark.
• Double-click in the center of the mark
and enter Width and Height values.
NOTE: For horizontal marks, the Width
value must be the same as the Width
specified previously (20 in this example).
• Click OK.
• Click RANGE again to save.
7
• Click CENTER.
Continued on next page