00198171-02_Technical_Training_FSE_TX-Series_EN.pdf - 第131页

8 Control and Communication 8.12 Excercise: Control and Communication Technical Training FSE SIPLACE TX-Series 01/2018 131 8.12 Excercise: Control and Communication 1. Which of the following statements is true regarding …

8 Control and Communication

8.11 Analysis - Common Error List

130 Technical Training FSE SIPLACE TX-Series 01/2018

8.11 Analysis - Common Error List

Code Error Description Possible Cause Action

30447

30451

30456

30256

30262

●

Communication on GCU-

GCU fast drive bus inter-

rupted

●

Specified CAN bus is

switched off

●

Secondary CAN bus is off

●

Cannot initialize CAN

hardware

●

Cannot initialize CAN inter-

face

●

Problem with cable

connection

●

Problem with CIN

●

Problem with certain

content/board in the

CAN circuit

●

Defective MGCU

●

Defect adapter/HCU

●

Check cable con-

nection

●

Restart the

machine

●

Check the status

and switch setting

on the CIN

●

Check and redown-

load firmware of

the CAN interface

●

Check status / in-

dication on the

board related in

CAN circuit

●

Check status / in-

dication of MGCU/

HMCU

●

Replace adapter/

HCU

37752

●

The LED test of the cam-

era illumination failed

●

No image captured from

camera

●

Power for illumination

of camera failed

●

LED failed but camera

can be operated

●

Problem with camera

GigE

●

Problem of cable GigE

●

Check relevant cir-

cuit of power for il-

lumination

●

Check output relev-

ant power supply

(PS)

●

Check the function-

ality of camera

●

Check connection

of the GigE cable

33378

33520

33606

33331

●

Camera cannot be ad-

dressed

●

Board camera cannot be

addressed

●

Image capture from cam-

era canceled

●

Signal path between

PC and camera inter-

rupted

●

Problem with camera

●

Check cable con-

nection on BoxPc

●

Check the coax

cable connection

and trailing cable

connector

●

Check the camera

cable

●

Check the camera

and replace if ne-

cessary

30365

30572

●

Moving the axis is not per-

mitted, Z Axis is not in a

safe position

●

Incorrect time sequence

when moving Star and Z

Axis

●

Sporadic communica-

tion error for axis con-

trol sequence

●

Permitted overlap re-

gion of Star and Z

been reached

●

Perform head axis

reference run

●

Check the head

and axis

●

Perform overall ref-

erence run

●

If certain segment

defective, replace it

8 Control and Communication

8.12 Excercise: Control and Communication

Technical Training FSE SIPLACE TX-Series 01/2018 131

8.12 Excercise: Control and Communication

1. Which of the following statements is true regarding TX communication system?

A CIN Box is instead of communication board (CAN bus card).

B Vision GigE system is instead of vision hotlink system.

C There are three different bus systems, CAN bus, Gantry CAN bus and FDB.

D All of the above.

2. Which parts do not communicate with the BOXPC via the CAN bus system in TX?

A CIN-Box.

B Conveyor controller (TSP).

C FCU (Feeder control unit), MHCU and MGCU.

D I/O unit (input/ output module).

3. Which of the following statements is true regarding parts exchange?

A No setting required after exchanging a MGCU.

B No setting required after exchanging a MHCU.

C No setting required after exchanging a FCU.

D No setting required after exchanging a CIN-Box.

4. CIN-Box is connected to BoxPC with CAT5 cable, and uses CAN bus cable to commu-

nicate with subsystem.

True …………………………………………………………………………………………………

False …………………………………………………………………………………………………

5. List all of subsystems which are controlled by CAN bus.

………………………………………………………………………………………………………

6. List the parts which are controlled by FCU.

………………………………………………………………………………………………………

8 Control and Communication

Room for Your Sketches and Notes

132 Technical Training FSE SIPLACE TX-Series 01/2018

Room for Your Sketches and Notes