00198171-02_Technical_Training_FSE_TX-Series_EN.pdf - 第59页

5 Component Supply 5.9 Excercise: Component Supply Technical Training FSE SIPLACE TX-Series 01/2018 59 Code Error Description Possible Cause Action 30551 30552 ● Cannot open nozzle changer ● Cannot closed nozzle changer …

5 Component Supply

5.8 Analysis - Common Error List

58 Technical Training FSE SIPLACE TX-Series 01/2018

5.7.1 Nozzle Changer Twin Head

1. Standard magazine

2. Positioning fiducials

3. Nozzle garage

4. Magazine for special nozzles

5. Nozzle garage for special nozzles

6. Balls for lifting the nozzles

This nozzle changer can accommodate up to 8 nozzle magazines. There are two different

magazine

types available: standard magazines and magazines for special nozzles or grippers.

The magazine for standard nozzles has 1 positioning fiducial for position detection, while the

magazine for special nozzles/grippers has two positioning fiducials. The nozzles are fixed in the

holder. They are then either locked for return or released for pickup, depending on the direction of

rotation of the D Axis.

Standard configuration:

●

3 magazines with two nozzle garages each.

●

1 magazine with one nozzle garage.

5.8 Analysis - Common Error List

Code Error Description Possible Cause Action

35410

35411

35412

35413

●

Left cutter not retracted

●

Left cutter not extended

●

Right cutter not retracted

●

Right cutter not extended

●

Incorrect proximity

switch position

●

Defective proximity

switch

●

Defective valve

●

Short of compressed

air

●

Defective cylinder

●

Check & adjust the

position of proximity

switch

●

Replace the switch

if necessary

●

Check power &

functionality of the

valve

●

Check compressed

air supply

●

Replace defective

cylinder

34946

34874

31820

35005

●

Stepping of feeder is not

possible

●

Feeder: tape drive error

●

Component was not trans-

ported into the specified

position

●

Tape is jammed or

twisted

●

Tape drive is faulty

●

Toothed wheel is

jammed

●

Check tape feeder

●

Replace the tape

drive or the feeder

●

Check the toothed

wheel and remove

any components

35401 Tape obstructed in tape duct or

couldn’t be cut

●

Stick tape material

used

●

Incorrect position of

cutter blade

●

Worn cutter blade

●

Check tape sticki-

ness

●

Test different

component tape for

cutting

●

Replace cutter

blade if necessary

5 Component Supply

5.9 Excercise: Component Supply

Technical Training FSE SIPLACE TX-Series 01/2018 59

Code Error Description Possible Cause Action

30551

30552

●

Cannot open nozzle changer

●

Cannot closed nozzle

changer

●

Nozzle inserted incor-

rectly

●

Components in

nozzle changer

●

Check nozzle

changer for incor-

rect inserted nozzle

or components

Use station software to

check function

5.9 Excercise: Component Supply

1. Which of the following statements is true regarding the TX component supply?

A The component table can be used on SX4 or XS machine.

B Additional retrofitting is necessary for second level reel support.

C The tape waste bin is an industry standard box.

D The use of a JTF-ML is possible on both location1 and 2.

2. Location 1, track 13-1, 2X8mm feeder, the chip component cannot be pick up, please

list possible reason.

………………………………………………………………………………………………………

5 Component Supply

Room for Your Sketches and Notes

60 Technical Training FSE SIPLACE TX-Series 01/2018

Room for Your Sketches and Notes