JO-109-002_JG-0209.pdf - 第20页
JO-1 16 Safe-12 1 105-001 5. Precautionary Items for Correct Operations 5. Precautionary Items for Correct Operations Requirements for Installation A void any place that vibrates severely . The ambient temperatures m…
JO-116
Safe-111105-001
4. Alert Indications in Instruction Manual
Alert Indications described as "
CAUTION
" (continued)
Alert Description Related Items
Avoid getting your nger caught in the toggle clamp while
fastening the tape feeder to the jig.
Section 4
2. Feeder
Measurement
If you detach the tape feeder with the master tapes being
attached from jig, you may cut your nger with sharp edges of
the master tapes or damage the tapes by bending the master
tapes, etc.
Be sure to detach the master tapes rst, then the tape feeder
from the jig.
Section 4
2. Feeder
Measurement
The master tapes are made of a thin metal. Carefully handle the
tapes to avoid cutting your nger with the tape edges.
Section 4
2.3.2 Detachment
of Master
Tape(s)
Carefully handle the dial gauge because the tip of the probe is
very sharp. Your hand will get injured if the tip is inserted.
Section 4
3.2 Measuring
Method
Safety Precautions
JO-116
Safe-121105-001
5. Precautionary Items for Correct Operations
5. Precautionary Items for Correct Operations
Requirements for Installation
Avoid any place that vibrates severely.
The ambient temperatures must be 20 ± 10
°
C and humidity 30 to 80 %.
Any dew condensation must be avoided.
When the machine is transferred to another place and the ambient temperature rises more
than the surface of the machine, dew may condense under the condition described below.
Note that dew condensation may cause the machine to break down.
Condition of Dew Condensation
Dew may condense when the difference (based on "Humidity (%)") between the ambient
temperature of the destination (the place where the machine was transferred) and the
surface temperature of the machine reaches the values or more in the table below.
Humidity (%) of Destination
Differences between Ambient Temperature of Destination
and Surface Temperature of Machine
80 3
°
C or more
70 6
°
C or more
60 8
°
C or more
50 10
°
C or more
40 14
°
C or more
30 18
°
C or more
Ensure that the selected place is free of electric noise, etc.
Precautionary measures (prevention of noise generation, etc.,) must be taken for other
equipment to prevent the machine from malfunctioning.
Do not expose the machine to combustible or corrosive gas.
Select a place free of lamp soot and dust.
Safety Precautions
JO-116
Safe-131105-001
5. Precautionary Items for Correct Operations
Power Supply
Conrm that the following power is supplied to this jig
Voltage : 220 V
±
10% AC
Before inserting the power plug, be sure to check the voltage and conrm that it matches
the specied one. Otherwise, the jig unit may break down.
And uctuating voltage and noise in the power line can have not only a bad inuence on
the machine but also trigger a malfunction of the machine, causing an accident.
Take necessary measures to prevent the other equipment from generating noises.
The preparation and connection of the primary power unit must be made on the
customer side.
Power Failure
Instantaneous voltage drop due to power failure or lightning will cause the built-in
computer to break down and the basic and application programs to corrupt.
It is recommended that a DC uninterruptive power supply be used as a countermeasure
against instantaneous voltage drop.
Personal Computer
The provided personal computer is used to save or output the measured data. When the
power is cut off while the computer is working (computer being accessed), the computer
may break down, causing the stored data and software programs to corrupt.
Reference
Refer to "2.2 Ending the Program" in "Section 2" for details.
Safety Precautions