00196504-02_UM_X-Serie_SR70X_EN.pdf - 第339页
User manual SIPLACE X-series Tasks on the machine From software version SR.70x.xx 01/2011 EN edition Obse rve LCD and status displays on the X feeder module 339 Low Voltage (Low voltage) Red 24V supply voltage rose above…
Tasks on the machine User manual SIPLACE X-series
Observe LCD and status displays on the X feeder module From software version SR.70x.xx 01/2011 EN edition
338
PLEASE NOTE 5
The machine controller switches off the status display of any feeder modules not included in the
set-up. The "LED off" status only occurs when the programming system has preset a job on the
line. This takes some of the work away from the operator since he only has to watch those feeder
modules that are contained in the set-up.
For the actual set-up process - no set-up information at the station, no job sent from SIPLACE
Pro to the station/line - the LED on each feeder module is activated after the set-up has been
made. The operator is thus informed whether everything is OK.
5.11.2 LCD display
The following tables containing the wording of the LCD display, the color and the mode of the sta-
tus display, its meaning and troubleshooting measures.
5.11.2.1 Warnings and remedies
5
5
5.11.2.2 Error messages and remedies
5
Text on the
LCD display
Status
display
Meaning Trouble-shooting
Remove Foil
(Remove the foil)
Orange The selected function is not
permitted when the cover foil
is tensioned (foil rocker is
pressed down).
If you wish to carry out that function, remove
the foil from the pair of gear wheels and cut
it off to relieve the pressure on the foil rocker.
Text on the
LCD display
Status
display
Meaning Trouble-shooting
None Red,
flashing
Feeder module software not
jumping to the application
Reload the application software
Load feeder module software
Handle --->>
(Handle --->>)
Red Feeder module was sig-
naled, but removal handle is
not yet pushed in
Push in the removal handle
Low Voltage
(Low voltage)
Orange 24V supply voltage did not
rise above the switch-on
threshold after switching on
Check the power supply
User manual SIPLACE X-series Tasks on the machine
From software version SR.70x.xx 01/2011 EN edition Observe LCD and status displays on the X feeder module
339
Low Voltage
(Low voltage)
Red 24V supply voltage rose
above the switch-on thresh-
old after switching on and
was then interrupted
Check the power supply
Feed Timeout
TransTimeout
(Timeout in tape
feeder -cycle)
Red Tape feeder cycle did not
end correctly within the spec-
ified time (timeout for the
"Feed" function)
Is the tape reel jammed in the container?
Is there a component jammed in the pick-up
area between component tape and compo-
nent window?
Once the obstacle has been eliminated, use
the arrow keys to restart the conveyor. The
feeder module will move the defective con-
veyor to the end, and then returned to its
position
Foil Torn
(Foil torn)
Red Foil was not tensioned within
the specified time
The foil is probably torn. Insert new foil and
tension
Foil PeelErr
(Error while peel-
ing off the foil)
Red Foil was not peeled off even
though the tape is moved
The cover foil is probably jammed beneath
the pick-up window and cannot be peeled
off correctly
Foil Jam
(Foil jam)
Red Foil motor has locked up Leveling gears blocked by foil? => Remove
the foil
EEP-WriteErr
(Error while back-
ing up data in the
EEPROM)
Red The data back-up in the EE-
PROM was not carried out
correctly
Remove the component tape (tape can be
moved out by pressing the arrow keys or
pulled out after raising the pick-up window).
Press the SET button to confirm the error.
Then press the yellow button to confirm the
reference run prompt.
EEP-ReadErr
(Error while read-
ing the
EEPROMS
Red Data was not read from the
EEPROM correctly
EEP-DataErr
(Error while back-
ing up the data in
the EEPROM)
Red The data back-up in the EE-
PROM was not carried out
fully
Reference o
Reference o
Red Position information is no
longer available for the com-
ponent tape drive
Remove the component tape (tape can be
moved out by pressing the arrow keys or
pulled out after raising the pick-up window).
Then press the "FOIL" button to start the
reference run.
CAN BusError
(CAN bus error)
Red CAN bus error Log off and on again, check the optical fiber
interface
Text on the
LCD display
Status
display
Meaning Trouble-shooting
Tasks on the machine User manual SIPLACE X-series
Changing the set-up From software version SR.70x.xx 01/2011 EN edition
340
PLEASE NOTE 5
Remove the component tape before a reference run.
5.12 Changing the set-up
5.12.1 Printing out the conversion instructions before changing the set-up
Before a change of set-up, print out the conversion instructions on the printer for the SIPLACE Pro
computer as described in the "SIPLACE Pro" manual or in the online help.
5.12.2 What you should note when changing the feeder modules
→ Handle the feeder modules carefully when you insert them into or remove them from the com-
ponent table. Make sure that the X feeder modules do not bump against the centering bar
(see item 5 in Fig. 5.10 - 3
, page 330) of the component table.
→ Vacuum the supporting surfaces of the feeder modules and clean the surface of the compo-
nent table when necessary according to the instructions in the preventive maintenance man-
ual.
→ Remove loose components using a
brush or a vacuum cleaner with a suitable nozzle.
CAUTION 5
Avoid using your fingers to remove components from the component table as the tiny metal
splinters can cause injury.
ParNotSaved! Red Parameters were not saved Default parameters are loaded automatical-
ly, i.e. the most recent operator settings are
overwritten -> The settings (e.g. increment)
will have to be made again. Replace the
control board if this error occurs frequently.
ParWrongSave Red Wrong or incomplete param-
eters were saved
BootFlashErr
FlashDataErr
Red Can no longer write to boot
or application memory cor-
rectly
Replace the feeder module or control board
Text on the
LCD display
Status
display
Meaning Trouble-shooting