00196504-02_UM_X-Serie_SR70X_EN.pdf - 第390页

Station extensions User manual SIPLACE X-series Docking station for the SIPLACE X-ser ies CO trol ley From software version SR.70x.xx 01/2011 EN edition 390 6.2.5.1 T ools Y o u will need the following tools and equipmen…

100%1 / 448
User manual SIPLACE X-series Station extensions
From software version SR.70x.xx 01/2011 EN edition Docking station for the SIPLACE X-series CO trolley
389
6.2.5 Adapting the docking station to the PCB conveyor height
The component trolley docking unit can be adjusted to PCB conveyor heights of 830 mm, 900 mm,
930 mm and 950 mm in just a few simple actions.
6
Fig. 6.2 - 5 Adapting the component trolley docking unit to the PCB conveyor heights
(1) Holes for the PCB conveyor height
(2) Hexagonal nut M8 and washer, 2x
(3) Hexagonal nut M8 and washer, 2x
(4) Hexagonal nut M8 and washer, 2x
(5) Slot for height adjustment
(6) Hexagon socket head screw M8x40, 6x
(7) Hexagon socket head screw M5x12, 4x
(8) Guide
(9) Hexagon socket head screw M8x18, 2x
(10) Side section, component trolley docking unit
(11) Paneling on the docking station
(12) Feeder module control unit (FCU)
Station extensions User manual SIPLACE X-series
Docking station for the SIPLACE X-series CO trolley From software version SR.70x.xx 01/2011 EN edition
390
6.2.5.1 Tools
You will need the following tools and equipment to adjust the height for the component trolley
docking unit:
– Allen key, set
– Fork wrench, size 13
6.2.5.2 Converting the CO trolley docking unit to other heights
WARNING 6
→ Disconnect the docking station from the main power supply.
→ Disconnect the docking station from the compressed air supply
The weight of the component trolley docking unit is approx. 40 kg.
→ Please ask a second person to help you with the conversion if necessary.
→ Note the order of the steps described.
6.2.5.3 Converting the CO trolley docking unit to a height of 830 mm or 900 mm
6
Fig. 6.2 - 6 Steps for conversion from a height of 830 mm to a height of 900 mm
→ Remove the two hexagon socket head screws M8x18 (item 9 in Fig. 6.2 - 5, page 389) and
remove the left and right guides (item 8 in Fig. 6.2 - 5
, page 389).
User manual SIPLACE X-series Station extensions
From software version SR.70x.xx 01/2011 EN edition Docking station for the SIPLACE X-series CO trolley
391
6
PLEASE NOTE: 6
Only remove the panel (item 9 in Fig. 6.2 - 5
, page 389) in the following situations:
– You are converting the component trolley docking unit to a height of 830 mm.
– You are converting the component trolley docking unit height of 830 mm to another height.
→ Remove the 4 hexagon socket head screws M5x12 (item 7 in Fig. 6.2 - 5
, page 389). Hold the
panel tightly so that it does not drop down.
→ Remove the panel.
CAUTION 6
Be careful not to damage any cables while raising and lowering the component trolley docking
unit.
→ Release both screw connections (item 3 in Fig. 6.2 - 5
, page 389).
→ Loosen both screw connections (item 2 in Fig. 6.2 - 5
, page 389).
→ Remove both M8 hexagonal nuts and washers (item 4 in Fig. 6.2 - 5
, page 389).
→ Hold the component trolley docking unit firmly by the side panel (item 10 in Fig. 6.2 - 5
, page
389
) while you remove the two hexagon socket head screws M8x40 at this point.
→ Swivel the component trolley docking unit upwards until the hole in the side section is covered
with the slot (item 5 in Fig. 6.2 - 5
, page 389).
→ Fasten the side section at this location. Only hand-tighten the nuts.
→ Hold the component trolley docking unit firmly by the FCU (item 12 in Fig. 6.2 - 5
, page 389)
while you remove the screwed connections at item 2 in Fig. 6.2 - 5
, page 389.
→ Swivel the component trolley docking unit upwards until the hole in the side section is covered
with the 900 mm hole (item 1 in Fig. 6.2 - 5
, page 389).
→ Fasten the side section at this location. Only hand-tighten the nuts.
→ Swivel the component trolley docking unit from the slot (item 5 in Fig. 6.2 - 5
, page 389 to the
900 mm hole upwards and fixed in place firmly at this location.
→ Check all screw connections at items 2, 3 and 4 in the 900 mm component trolley height for
firm seating.
→ Fix the left and right guides (item 8 in Fig. 6.2 - 5
, page 389) using the hexagon socket head
screw M8x18 (item 9 in Fig. 6.2 - 5
, page 389).
→ Fix the panel (item 11 in Fig. 6.2 - 5
, page 389) using the 4 hexagon socket head screw M5x12
(item 7 in Fig. 6.2 - 5
, page 389) .