00196504-02_UM_X-Serie_SR70X_EN.pdf - 第340页

Tasks on the machine User manual SIPLACE X-series Changing the set-up From software version SR.70x.xx 01/2011 EN edition 340 PLEASE NOTE 5 Remove th e compone nt tape before a referenc e run. 5.12 Changing the set-up 5.1…

User manual SIPLACE X-series Tasks on the machine

From software version SR.70x.xx 01/2011 EN edition Observe LCD and status displays on the X feeder module

339

Low Voltage

(Low voltage)

Red 24V supply voltage rose

above the switch-on thresh-

old after switching on and

was then interrupted

Check the power supply

Feed Timeout

TransTimeout

(Timeout in tape

feeder -cycle)

Red Tape feeder cycle did not

end correctly within the spec-

ified time (timeout for the

"Feed" function)

Is the tape reel jammed in the container?

Is there a component jammed in the pick-up

area between component tape and compo-

nent window?

Once the obstacle has been eliminated, use

the arrow keys to restart the conveyor. The

feeder module will move the defective con-

veyor to the end, and then returned to its

position

Foil Torn

(Foil torn)

Red Foil was not tensioned within

the specified time

The foil is probably torn. Insert new foil and

tension

Foil PeelErr

(Error while peel-

ing off the foil)

Red Foil was not peeled off even

though the tape is moved

The cover foil is probably jammed beneath

the pick-up window and cannot be peeled

off correctly

Foil Jam

(Foil jam)

Red Foil motor has locked up Leveling gears blocked by foil? => Remove

the foil

EEP-WriteErr

(Error while back-

ing up data in the

EEPROM)

Red The data back-up in the EE-

PROM was not carried out

correctly

Remove the component tape (tape can be

moved out by pressing the arrow keys or

pulled out after raising the pick-up window).

Press the SET button to confirm the error.

Then press the yellow button to confirm the

reference run prompt.

EEP-ReadErr

(Error while read-

ing the

EEPROMS

Red Data was not read from the

EEPROM correctly

EEP-DataErr

(Error while back-

ing up the data in

the EEPROM)

Red The data back-up in the EE-

PROM was not carried out

fully

Reference o

Red Position information is no

longer available for the com-

ponent tape drive

Remove the component tape (tape can be

moved out by pressing the arrow keys or

pulled out after raising the pick-up window).

Then press the "FOIL" button to start the

reference run.

CAN BusError

(CAN bus error)

Red CAN bus error Log off and on again, check the optical fiber

interface

Text on the

LCD display

Status

display

Meaning Trouble-shooting

Tasks on the machine User manual SIPLACE X-series

Changing the set-up From software version SR.70x.xx 01/2011 EN edition

340

PLEASE NOTE 5

Remove the component tape before a reference run.

5.12 Changing the set-up

5.12.1 Printing out the conversion instructions before changing the set-up

Before a change of set-up, print out the conversion instructions on the printer for the SIPLACE Pro

computer as described in the "SIPLACE Pro" manual or in the online help.

5.12.2 What you should note when changing the feeder modules

→ Handle the feeder modules carefully when you insert them into or remove them from the com-

ponent table. Make sure that the X feeder modules do not bump against the centering bar

(see item 5 in Fig. 5.10 - 3

, page 330) of the component table.

→ Vacuum the supporting surfaces of the feeder modules and clean the surface of the compo-

nent table when necessary according to the instructions in the preventive maintenance man-

ual.

→ Remove loose components using a

brush or a vacuum cleaner with a suitable nozzle.

CAUTION 5

Avoid using your fingers to remove components from the component table as the tiny metal

splinters can cause injury.

ParNotSaved! Red Parameters were not saved Default parameters are loaded automatical-

ly, i.e. the most recent operator settings are

overwritten -> The settings (e.g. increment)

will have to be made again. Replace the

control board if this error occurs frequently.

ParWrongSave Red Wrong or incomplete param-

eters were saved

BootFlashErr

FlashDataErr

Red Can no longer write to boot

or application memory cor-

rectly

Replace the feeder module or control board

Text on the

LCD display

Status

display

Meaning Trouble-shooting

User manual SIPLACE X-series Tasks on the machine

From software version SR.70x.xx 01/2011 EN edition Avoiding track errors

341

5.13 Avoiding track errors

5.13.1 General

→ Make sure that the areas around the feeder modules are clean and that there are no loose

components in the feeder area or under the feeder modules.

→ Refill promptly with components.

→ Splice the tapes early. This generally means that you are to prepare the splicing material

when there is still approximately 1.5 m of tape on the reel.

→ Handle the feeder modules carefully when you insert them into or remove them from the com-

ponent table as these are high-precision devices.

→ For X feeder modules, lower the pick-up window since it can easily be damaged when raised.

PLEASE NOTE 5

A raised pick-up window leads to noticeably impaired pick-up quality.

→ Check that the pick-up position is set correctly for the components on the feeder modules.

5.13.2 Avoiding track errors with the tape container

→ Insert the separating plates correctly (see Fig. 5.9 - 3, page 326).