00197082-03_AI_MTC2_at-Loc2_X-Series-S_DE_EN.pdf - 第52页
1 Introduction 1.5 Abbreviations 52 Assembly Instructions / Montageanleitung SIPLACE X-Series S MTC2 at Location 2 MTC2 an Stellplatz 2 05/2019
1 Introduction
1.4 Staff qualifications and training
Assembly Instructions / Montageanleitung SIPLACE X-Series S MTC2 at Location 2 MTC2 an Stellplatz 2 05/2019 51
1.3.3.5 Dispatching ESD modules
► Always store modules and components in conductive packaging (e.g. metallized plastic bags
or metal sleeves) and dispatch them in conductive packaging
► If the packaging is not conductive, place the modules in a conductive envelope before pack-
aging. Use conductive expanded rubber, ESD bags, domestic aluminum foil or paper, for
example. NEVER use plastic bags or film.
► If the module has integral batteries, ensure that the conductive packaging does not touch or
short circuit the battery terminals and, if necessary, first cover the terminals with insulating
tape or material.
1.3.4 Release History
Document
SIPLACE X-Series S
MTC2 at location 2
Assembly Instructions
Release Amendments
05/2013 Initial release
10/2013 Revision
05/2019 Amendments and supplements:
●
Safety instructions – updated
●
Scope of delivery, parts lists – updated
●
Preconditions – updated
●
Replacing the bottom plexiglass sheet on the cover – supplemented
1.4 Staff qualifications and training
Qualified or adequately trained personnel means that these people are familiar with the setting up,
operation and maintenance of the machine and the add-on devices and are suitably qualified, e.g.:
●
Have been trained, instructed or authorized to switch on and off, isolate, earth and identify
electrical circuits and system components in accordance with normal safety standards.
●
Have been trained or instructed in the upkeep and use of appropriate safety equipment in
accordance with normal safety standards.
●
Have received first aid training.
1.5 Abbreviations
Abbreviation Description
CO Component
COT Changeover table
COT-i Changeover table insert
C&P Collect&Place
CPP Collect&Pick&Place head
ESD Electrostatic sensitive device
EMC Electromagnetic compatibility
MTC Matrix Tray Changer
NC Nozzle changer
TH TwinHead
1 Introduction
1.5 Abbreviations
52 Assembly Instructions / Montageanleitung SIPLACE X-Series S MTC2 at Location 2 MTC2 an Stellplatz 2 05/2019
2 Brief Description
2.1 Product Description
Assembly Instructions / Montageanleitung SIPLACE X-Series S MTC2 at Location 2 MTC2 an Stellplatz 2 05/2019 53
2 Brief Description
This manual describes the conversion tasks required for installation of an MTC2 at location 2 of X2
S / X3 S / X4 S machines.
2.1 Product Description
The MTC2 consists of two independently working towers, which allow you to configure and fully
automatically change up to 100 JEDEC waffle pack trays.
To use an MTC at location 2 of the X2 S / X3 S / X4 S, you need to install an MTC slide-in frame-
work [03009963‑xx].
2.1.1 Overview of the Modules
Fig.7: MTC2
1. Feed axis 1
2. Feed axis 2
3. Interface plug for docking into the
placement machine
4. Electronic control unit
5. Integral chassis
6. Cable gland for the power supply cable
7. Tower 1
8. Tower 2
Tower 1 can accommodate a maximum of
30 XL waffle pack tray carriers with 60 JE-
DEC or 30 special magazines of maximum
size.
Tower 2 can accommodate a maximum of
40 waffle pack tray carriers with 40 JEDEC
waffle pack trays.
2.2 Requirements
For X4 S machines, configurations with an MTC at location 2 are generally possible in conjunction
with a Twin. Corresponding configurations with a CPP are available as a special configuration.
For machine types X3 S and X2 S, configurations with an MTC at location 2 are generally possible
in conjunction with a Twin or a CPP head.
In addition to the MTC2, a service flap and an output extension or conveyor are fitted as a default.
Observe the following instructions for these:
●
Assembly instructions "SIPLACE X‑SeriesS service flap" [DE+EN: 00197396‑xx]
●
Assembly instructions "SIPLACE X‑SeriesS Input/output conveyor extension and hand
guard" [DE+EN: 00197089‑xx]