BA-UI-EN-D33363.pdf - 第10页
10 D33363 | Date 01/2020 Construction and description 2. Construction and description 2.1 Construction 1 2 3 4 7 8 5 6 Fig. 2 Construction 1 ControlCOCKPIT with capacitive function keys (see page 27) 2 On/Off switch (see…
D33363 | Date 01/2020 9
For your Safety
1.7 Switching off the appliance in an emergency
Push the On/Off switch on the control panel
( Fig. 1 ) and disconnect power plug. This
disconnects the appliance from the power
supply at all poles.
Warning!
Depending on the operation
performed , the surfaces in
the working chamber and
the chamber load may still
be very hot after the appli-
ance is switched off. Touch-
ing these surfaces can cause
burns. Wear heat-resistant
protective gloves or wait
until the appliance cools
down.
ON
O
O
ON
N
N
N
O
O
N
O
Fig. 1
Switch off the appliance by pressing the On/
Off switch
10 D33363 | Date 01/2020
Construction and description
2. Construction and description
2.1 Construction
1
2
3
4
7
8
5
6
Fig. 2 Construction
1 ControlCOCKPIT with capacitive function
keys (see page 27)
2 On/Off switch (see page 24)
3 Working chamber fan (for
UF
.../IF... appliances only)
4 Steel grid
5 Working chamber
6 Nameplate (covered, see page 13)
7 Door handle (see page 25)
8 Turn control with confirmation key
D33363 | Date 01/2020 11
Construction and description
2.2 Intended use
Based on the standards and guidelines listed in the following, the products described
in this manual have received a CE label from the company Memmert:
Product Intended use Directives
UNxx
UFxx
INxx
IFxx
This appliance is exclusively intended
for heating up non-explosive sub-
stances and objects. Any other use is
improper and may result in hazards
and damage.
The appliance is not explosion-proof
(does not comply with the German oc-
cupational health and safety regulation
VBG 24). The appliance may only be
loaded with materials and substances
which cannot form any toxic or explo-
sive vapours at the set temperature
and which cannot explode, burst or
ignite.
The appliance may not be used for the
drying, evaporation and burning-in of
paints or similar materials, the solvents
of which could form an explosive mix-
ture when combined with air. If there
is any doubt as to the composition of
materials, they must not be loaded into
the appliance. Potentially explosive gas-
air mixtures must not form, neither in
the working chamber nor in the direct
vicinity of the appliance.
► Directive 2004/108/EC amended
(Directive of the European Parlia-
ment and of the Council on the
approximation of the laws of the
Member States relating to electro-
magnetic compatibility). Standards
complied with:
DIN EN 61326:2004-05
EN 61326:1997
EN 61326/A1:1998
EN 61326/A2:2001
EN 61326/A2:2003
► Directive 2006/95/EC amended
(Directive of the European Parlia-
ment and of the Council on the
harmonisation of the laws of
Member States relating to electrical
equipment designed for use within
certain voltage limits). Standards
complied with:
DIN EN 61 010-1 (VDE 0411 part 1)
DIN EN 61 010-2-010 (VDE 0411
part 2-010)
EN 61 010-1:2001, EN 61 010-2-
010
Product Intended use as a medical device Directive
UNxxm
IN
xxm
UF
xxm
IF
xxm
The appliance may be used for heating
fango, silicate and APS packs for physi-
cal therapy and keeping them warm.
Directive 93/42/EEC (Council Directive
concerning medical devices)