BA-UI-EN-D33363.pdf - 第27页

D33363 | Date 01/2020 27 Operation and control TIMER End 14 : 45 44 h :44 m 180 .4 °C TEMP Set 180 .4 °C 20 % FLAP FAN % 0 FLAP 40 % 5 3 4 12 TIMER 30 m 04 h End 13:30 23.11. 11 12 67 8 9 1 0 Fig. 15 ControlCOCKPIT for U…

26 D33363 | Date 01/2020

Operation and control

5.3 Loading the appliance

Warning!

When loading the appliance with an unsuitable load, poisonous

or explosive vapours or gases may be produced. This could cause

the appliance to explode, and persons could be severely injured or

poisoned. The appliance may only be loaded with materials which do

not form any toxic or explosive vapours when heated up and cannot

ignite (see also page 11). If there is any doubt as to the composi-

tion of materials, they must not be loaded into the appliance.

Caution:

Check the chamber load for chemical compatibility with the materials of the appliance

(see page 12).

Caution:

If the chamber load is wet or very humid, water may accumulate on the floor and dam-

age the heater. If wet, use a drip tray on the bottom of the tube.

Insert the sliding steel grids or sliding shelves. The maximum number or grids / shelves and the

load capacity are specified in the technical data overview on page 14.

The chamber must not be

loaded too tightly, so that

proper air circulation in the

working chamber is guaran-

teed. Do not place any

chamber load on the floor,

touching the side walls or

right below the ceiling of the

working chamber (Fig. 14 , see

also the "correct loading"

sticker on the appliance).

In case of improper loading

(chamber loaded too tightly),

the set temperature may

be exceeded or it may take

longer until it is reached.

To achieve the correct heating capacity, the type of slide-in unit used – Grid or Shelf –

must be set in the menu under

SETUP (see page 41).

5.4 Operating the appliance

5.4.1 ControlCOCKPIT

In manual operation, the desired parameters are entered at the ControlCOCKPIT on the front

of the appliance (Fig. 15 and Fig. 16 ). You can also make basic settings here (menu). Addition-

ally, warning messages are displayed, e.g. if the temperature is exceeded.

Fig. 14 Correct placement of the chamber load

D33363 | Date 01/2020 27

Operation and control

TIMER

End 14 : 45

44h:44m

180.4 °C

TEMP

Set 180

.4 °C

20%

FLAP

FAN

FLAP

40 %

53 412

TIMER

30m04h

End

13:30 23.11.

11 1267 8 9 10

Fig. 15 ControlCOCKPIT for UF.../IF... appliances in operating mode

180.0 °C

Set 180.9 °C

TEMP

TIMER

End 14 : 45

44h:44m

FLAP

40 %

12 5

TIMER

30m04h

End

13:30 23.11.

10 11 1267 8 9

Fig. 16 ControlCOCKPIT for UN.../IN... appliances in operating mode

1 Activation key for temperature setpoint

adjustment

2 Setpoint and actual temperature display

3 Fan speed display

4 Activation key for fan speed setting

5 Switch to menu mode (see page 36)

6 Activation key digital backwards counter

with target time setting, adjustable from 1

minute to 99 days

7 On/Off switch

8 Display digital backwards counter with

target time setting, adjustable from 1 min-

ute to 99 days

9 Air flap position display

10 Activation key for air flap position adjust-

ment

11 Turn control for setpoint adjustment

12 Confirmation key (accepts setting made

with the turn control)

28 D33363 | Date 01/2020

Operation and control

5.4.2 Basic operation

In general, all settings are made according to the following pattern:

1. Activate the desired parameter (e.g. tem-

perature). To do so, press the correspond-

ing activation key on the left or right of

the respective display. The activated dis-

play is lined in colour, the other displays

are dimmed. The set value is highlighted

in colour.

. 5°C100

TEMP

TIMER

22.4 °C

TEMP

37.0 °CSet

2. By turning the turn control to the left

or right, adjust the set value (e.g. to

180.0 ºC).

3. Save the set value by pressing the confir-

mation key.

The display returns to normal and the

appliance begins adjusting to the defined

set value.

23.2 °C

TEMP

Set 180

.0 °C

Additional parameters (air flap position etc.) can be set accordingly.

If no new values are entered or confirmed for approx. 30 seconds, the appliance automati-

cally returns to the main menu and restores the former values.

If you want to cancel the setting procedure, press the

activation key on the left or right of the display that you

want to exit. The appliance restores the former values.

Only the settings that you have confirmed by pressing

the confirmation key before cancelling the setting

procedure are accepted.

5.4.3 Operating modes

The appliance can be operated in different modes:

► Manual mode: The appliance runs in permanent operation at the values set on the

ControlCOCKPIT. Operation in this mode is described in chapter 5.4.4.

► Operation with digital backwards counter with target time setting, adjustable from 1 min-

ute to 99 days (Timer): The appliance runs at the values set until the timer has elapsed.

Operation in this mode is described in chapter 5.4.5 .

► via remote control (see page 41)

22.4 °C

TEMP

180.0 °CSet