BA-UI-EN-D33363.pdf - 第36页
36 D33363 | Date 01/2020 Menu mode 7. Menu mode In menu mode, you can make basic settings as well as adjust appliance parameters. Caution: Before changing menu settings, read the description of the respective functions o…
D33363 | Date 01/2020 35
Malfunctions, warning and error messages
6.3 Power failure
Warning!
Depending on the operation performed, the surfaces in the interior
and the chamber load may still be very hot after power loss. Ad-
ditionally, depending on the duration of the power loss, the appli-
ance might heat up again after power supply has been restored (see
below). Touching these surfaces can cause burns. Wear heat-resistant
protective gloves or wait until the appliance cools down fi rst.
In case of a power failure, the appliance operates as follows:
In manual mode
After power supply has been restored, operation is continued with the parameters set. The
time and the duration of the power failure is documented in the protocol log memory.
In timer mode
In case of an interruption of the power supply of less than 60 minutes, the current timer is
continued from the point at which it was interrupted. For interruptions of the power supply
longer than this, all appliance functions (heating, fan etc.) are switched off and the air flap is
opened.
In remote control mode:
The previous values are restored.
36 D33363 | Date 01/2020
Menu mode
7. Menu mode
In menu mode, you can make basic settings as well as adjust appliance parameters.
Caution:
Before changing menu settings, read the description of the respective functions on the fol-
lowing pages to avoid possible damage to the appliance and/or chamber load.
To enter menu mode, press the MENU key.
To exit the menu mode at any time, press the MENU key
again. The appliance then returns to manual mode. Only
changes accepted by pressing the confirmation key are
saved.
7.1 Overview
Press the MENU key to change between the displays in menu mode:
SETUP
SIGNALTÖNE
CALIB
LANGUAGE
TIME
12 34 5
6789 1011
Fig. 21 ControlCOCKPIT in menu mode
1 Language selection activation key
2 Language selection display
3 Date and time display
4 Date and time setting activation key
5 Return to manual mode
6 Setup activation key (basic appliance set-
tings)
7 Setup display (basic appliance settings)
8 Adjustment display
9 Adjustment activation key
10 Turn control for adjustment
11 Confirmation key (accepts setting made
with the turn control)
D33363 | Date 01/2020 37
Menu mode
7.2 Basic operation in menu mode using the example of language
selection
In general, all settings in menu mode are done just like in manual mode: Activate the re-
spective display, use the turn control for setting and press the confirmation key to accept
the change. A more detailed description is provided in the following, using the example of
language selection.
1. Activate the desired parameter (in this
example the language). To do so, press
the corresponding activation key on the
left or right of the respective display. The
activated display is enlarged.
ENGLISH
DEUTSCH
ESPANOL
POLSKI
CESTINA
FRANCAIS
If you want to exit or cancel your settings,
again press the activation key which you
have used to activate the display. The
appliance returns to the menu overview.
Only the settings that you have con-
firmed by pressing the confirmation key
before cancelling the setting procedure
are accepted.
SETUP
SIGNALTÖNE
CALIB
LANGUAGE
TIME
ON
O
O
ON
N
N
N
O
O
N
O
2. With the turn control, select the desired
new setting, e.g. Español (Spanish).
3. Save the setting by pressing the confir-
mation key.
SPRACHE
ENGLISH
DEUTSCH
MAGYAR
ITALIANO
ESPANOL
FRANCAIS
POLSKI
CESTINA
4. To return to the menu overview, press the
activation key again.
SETUP
SIGNALTÖ
N
CALI
B
LANGUAGE
TIM
You can now
► activate another menu function by press-
ing the corresponding activation key or
► return to manual mode by pressing the
MENU key.
Balance
Einheit
IP Adresse
Alarm Tem
p
Timer Mod
e
Unit
IP address
Subnet mas
k
Alarm temp
Timer mode
Slide-in unit
SPRACHE
ENGLISH
DEUTSCH
MAGYAR
ITALIANO
ESPANOL
FRANCAIS
POLSKI