MDO3000 Programmer Manual.pdf - 第100页

Command Groups T able 2-39: Search Commands (cont.) Command Description SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:US B:DA T a: SIZe This command speci fi es the number of data bytes for USB searches SEARCH:SEARCH&lt…

100%1 / 1158
Command Groups
Table 2-39: Search Commands (cont.)
Command Description
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:MIL1553B :
STATus:PARity
When the MIL-STD-1553 bus search condition is set to STATus,
this command specifies the status parity bit value to be used in
the search.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:MIL1553B :
TIMe:LESSLimit
When the MIL-STD-1553 bus search condition is set to TI Me,this
command specifies either the minimum remote terminal response
time (RT) limit for the amount of time the terminal has to transmit, or
it specifies the m inimum inter-message gap (IMG).
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:MIL1553B :
TIMe:MORELimit
When the MIL-STD-1553 bus search condition is set to TI Me,this
command specifies either the maximum remote terminal response
time (RT) limit for the amount of time the terminal has to transmit, or
it specifies the m aximum inter-message gap (IMG).
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:MIL1553B :
TIMe:QUALifier
When the MIL-STD-1553 bus search condition is set to TI Me,this
command specifies the trigger data time qualifier.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:PARallel:
VALue
This command specifi esthebinarydatastringtobeusedfora
Parallel search
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:RS232C:
CONDition
This command specifies the search condition for an RS-232 trigger
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:RS232C:RX:
DATa:SIZe
This command specifies the length o f the data string for an
RS-232search, if the search condition is RX
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:RS232C:RX:
DATa:VALue
This command specifies the binary data string for an RS-232 search,
if the condition involves RX
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:RS232C:TX:
DATa:SIZe
This command speci fies the length of the data string to be used for
an RS-232 search, if the search condition is TX
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:RS232C:TX:
DATa:VALue
This command specifies the binary data string to be used for an
RS-232 search, if the condition involves RX
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:SPI:CONDition This command specifies the search condition for SPI search
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:SPI:DATa{:
MISO|:IN}:VALue
This command specifies the binary data string to be used for SPI
search if the search condition is MISO or MISOMOSI
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:SPI:DATa{:
MOSI|:OUT}:VALue
This command specifies the binary data string for an SPI search if
the search condition is MISO or MISOMOSI
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:SPI:DATa:SIZe This command specifies the length of the data string i n bytes to
be used for SPI search
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:USB :
ADDRess:HIVALue
This command specifies the high limit for USB address searches
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:USB :
ADDRess:VALue
This command specifies the value for USB address searches
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:USB :
CONDition
This command specifies the USB search condition.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:USB :DATa:
HIVALue
This command specifies the high limit for U SB data searches
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:USB :DATa:
OFFSet
This command specifies the data offset for USB data searches
MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual 2-69
Command Groups
Table 2-39: Search Commands (cont.)
Command Description
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:US B:DATa:
SIZe
This command specifies the number of data bytes for USB searches
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:US B:DATa:
TYPe
This command specifies the data type for USB searches
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:US B:DATa:
VALue
This command specifies the data value for USB data searches
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:US B:
ENDPoint:VALue
This command specifies the endpoint value for USB searches
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:US B:
ERRTYPE
This command specifies the error type for USB searches
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:US B:
HANDSHAKEType
This command specifies the handshake type for USB searches
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:USB:QU ALifier This command specifies the qualifier for USB searches
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:US B:
SOFFRAME NU M ber
This command specifies the S OF number for USB searches
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:US B:
SPECIALType
This command specifies the special packet type for USB searches
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:US B:SPLit:E T:
VALue
When searching on a high-speed USB split transaction, this
command specifies the split transaction endpoint type value to
search for.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:US B:SPLit:
HUB:VALue
When searching on a high-speed USB split transaction, this
command specifies the split transaction hub address value to
search for.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:US B:SPLit:
PORT:VALue
When searching on a high-speed USB split transaction, this
command specifies the split transaction port address value to
search for.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:US B:SPLit:SC:
VALue
When searching on a high-speed USB split transaction, this
command specifies whether to search for the start or complete
phase of the split transaction, based on the Start/Complete bit field
value.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:US B:SPLit:S E:
VALue
When searching for a high-speed USB split transaction, this
command specifies the split transaction start/end bit value to search
for.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:US B:
TOKENType
This command specifies the token type for USB searches
SEARCH:SEARCH<x>:TRIGger:A:BUS:SOU rc e This command specifies the bus for a serial search
SEARCH:SEARCH<x>:TRIGger:A:EDGE:SLOpe This command specifies the slope to be used in an edge search:
rising, falling or either
SEARCH:SEARCH<x>:TRIGger:A:EDGE:SOUrce This command specifies the source waveform for an edge search
SEARCH:SEARCH<x>:TRIGger:A:LEVel:CH<x>
Sets the threshold level to use when searching on an analog
waveform.
2-70 MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual
Command Groups
Table 2-39: Search Commands (cont.)
Command Description
SEARCH:SEARCH<x>:TRIGger:A:LEVel:MATH
Sets the threshold level to use when searching on the math
waveform.
SEARCH:SEARCH<x>:TRIGger:A:LEVel:REF<x>
Sets the threshold level to use when searching on a reference
waveform.
SEARCH:SEARCH<x>:TRIGger:A:LEVel:RF_AMPlitude
Sets the threshold level to use when searching on the RF Amplitude
vs. Time trace.
SEARCH:SEARCH<x>:TRIGger:A:LEVel:RF_FREQuency
Sets the threshold level to use when searching on the RF Frequency
vs. Time trace.
SEARCH:SEARCH<x>:TRIGger:A:LEVel:RF_PHASe
Sets the threshold level to use when searching on the RF Phase
vs. Time trace.
SEARCH:SEARCH<x>:TRIGger:A:LOGIc:FU NCtion Specifies the logic operator to be used in a logic search.
SEARCH:SEARC H<x>:T RIG ger:A:LO G Ic:PATtern:INPut:
CH<x>
This command specifies the logic operator for the logic search
SEARCH:SEARC H<x>:TRIGger:A:LOGIc:INPut:CH<x> Specifies the l ogic condition to be used in a logic search when the
input is an analog channel.
SEARCH:SEARC H<x>:TRIGger:A:LOGIc:INPut:CLOCk:
EDGE
This command specifies whether the clock edge is rise or fall for
a logic search
SEARCH:SEARC H<x>:TRIGger:A:LOGIc:INPut:CLOCk:
SOUrce
This command specifies the clock source de finition for logic search
SEARCH:SEARC H<x>:TRIGger:A:LOGIc:INPut:D<x> This command specifies the criteria for a logic search to determine
where to place a mark for digital channel <x>
SEARCH:SEARC H<x>:T RIG ger:A:LO G Ic:IN Put:M ATH This command specifies the Boolean logic criteria for the logic
search
SEARCH:SEARC H<x>:T RIG ger:A:LOGIc:INPut:REF<x> This command specifies the Boolean logic criteria for the logic
search
SEARCH:SEARCH<x>:TRIGger:A:LOGIc:INPut:
RF_AMPlitude
This command specifies the logic criteria to search for when
searching using the RF Amplitude vs. Time trace. This command
is used together with SEARCH:SEARCH<x>:TRIGger:A:LOGIc:
THReshold:RF_AMPlitude to search for an instance when the
waveform goes higher or lower than the specified threshold.
SEARCH:SEARCH<x>:TRIGger:A:LOGIc:INPut:
RF_FREQuency
This command specifies the logic criteria to search for when
searching using the RF Frequency vs. Time trace. This command
is used together with SEARCH:SEARCH<x>:TRIGger:A:LOGIc:
THReshold:RF_FREQuency to search for an instance when the
waveform goes higher or lower than the specified threshold.
SEARCH:SEARC H<x>:TRIGger:A:LOGIc:INPut:RF_PHAS e This command speci fies the logic criteria to search for when
searching using the RF Phase vs. Time trace. This command
is used together with SEARCH:SEARCH<x>:TRIGger:A:LOGIc:
THReshold:RF_PHASe to search for an instance when the
waveform goes higher or lower than the specified threshold.
SEARCH:SEARC H<x>:T RIG ger:A:LO G Ic:PATtern:WHEn This command specifies the condition for generating a logic pattern
search.
MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual 2-71