MDO3000 Programmer Manual.pdf - 第726页

Commands Listed in A lphabetical Order SEARCH:SEARC H<x>:TRIGger:A:BUS:B<x>:RS232C:CONDition This command specifies the condition to be u sed in an RS-232 search. SEARCH< x> is the search number , which …

100%1 / 1158
Commands Listed in Alphabetical Order
Conditions
This command re
quires a DPO4AERO application module for DPO/MSO4000B
and MDO4000/B/C models or MDO3AERO application module for
MDO3000 models.
Group
Search
Syntax
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:MIL1553B:TIMe:QUALifier
{LESSthan|MOREthan|INrange|OUTrange}
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:MIL1553B:TIMe:QUALifier?
Related Commands
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:MIL1553B:CONDition
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:MIL1553B:TIMe:LESSLimit
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:MIL1553B:TIMe:MORELimit
Arguments
LESSthan sets the Time qualifier to less than minimum.
MOREthan sets the Time qualifier to greater than maximum
INrange sets the Time qualifier to inside range.
OUTrange sets the Time qualifier to out of range.
Examples
SEARCH:SEARCH1:TRIGger:A:BUS:B1:MIL1553B:TIMe:QUALifier
LESSthan
sets the Time qualifier to less than minimum.
SEARCH:SEARCH1:TRIGger:A:BUS:B1:MIL1553B:TIMe:QUALifier?
might return OUTRANGE.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:PARallel:VALue
This command specifies the data value to be used in a Parallel search. SEAR CH<x>
is the search number and B<x> SEARCH<x> is the search number, which is always
1, and
B<x>
Group
Search
Syntax
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:PARallel:VALue <QString>
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:PARallel:VALue?
Arguments
<QString> is the binary data string.
MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual 2-695
Commands Listed in Alphabetical Order
SEARCH:SEARC
H<x>:TRIGger:A:BUS:B<x>:RS232C:CONDition
This command specifies the condition to be used in an RS-232 search. SEARCH< x>
is the search number, which is always 1, and B<x>
Conditions
This command requires a DPO4COMP application module for DPO/MSO4000B
and MDO4000/B/C models or MDO3COMP application module for
MDO3000 models.
Group
Search
Syntax
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:RS232C:CONDition
{RXSTArt|RXDATA|RXENDPacket|TXSTArt|TXDATA|TXENDPacket}
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:RS232C:CONDition?
Arguments
RXSTArt specifies a search based on the RX Start Bit.
RXDATA specifies a search based on RX Data.
RXENDPacket specifies a search based on the RX End of Packet condition.
TXSTArt specifies a search base on the TX Start Bit.
TXDATA specifies a search based on TX Data.
TXENDPacket specifies a search based on the TX End of Packet condition.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:RS232C:RX:DATa:SIZe
This command specifies the length of the data string to be used in an
RS-232 search, if the search condition is set to
RXDATA. SEARCH<x> is the search
number, which is always 1, and
B<x>
Conditions
This command requires a DPO4COMP application module for DPO/MSO4000B
and MDO4000/B/C models or MDO3COMP application module for
MDO3000 models.
Group
Search
Syntax
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:RS232C:RX:DATa:SIZe
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:RS232C:RX:DATa:SIZe?
2-696 MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual
Commands Listed in Alphabetical Order
Related Commands
SEARCH:SEARCH
<x>:TRIGger:A:BUS:B<x>:RS232C:CONDition
Arguments
<NR1> is the length of the data string in Bytes.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:RS232C:RX:DATa:VALue
This command specifies the data value to be used in an RS-232 search, if the
condition is set to
RXDATA. SEARCH<x> is the search number, which is always
1, and
B<x>
Conditions
This command requires a DPO4COMP application module for DPO/MSO4000B
and MDO4000/B/C models or MDO3COMP application module for
MDO3000 models.
Group
Search
Syntax
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:RS232C:RX:DATa:VALue
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:RS232C:RX:DATa:VALue?
Related Commands
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:RS232C:CONDition
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:RS232C:TX:DATa:SIZe
This command specifies the length of the data string to be used for an
RS-232 search if the search condition is set to
TXDATA. SEARCH<x> is the search
number, which is always 1, and
B<x>
Conditions
This command requires a DPO4COMP application module for DPO/MSO4000B
and MDO4000/B/C models or MDO3COMP application module for
MDO3000 models.
Group
Search
Syntax
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:RS232C:TX:DATa:SIZe
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:RS232C:TX:DATa:SIZe?
Related Commands
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:RS232C:CONDition
MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual 2-697