MDO3000 Programmer Manual.pdf - 第494页

Commands Listed in A lphabetical Order PHOTO for a phot o print paper type. FASTPHOTO for a fastphoto print paper type. Examples PICTBRIDGE:PA PERTYPE PLAIN sets the paper type to Plain. PICTBRIDGE:PA PERTYPE? might retu…

100%1 / 1158
Commands Listed in Alphabetical Order
A7 for a A7 paper
size.
A8 for a A8 paper size.
A9 for a A9 paper size.
B0 for a B0 paper size.
B1 for a B1 paper size.
B2 for a B2 paper size.
B3 for a B3 paper size.
B4 for a B4 paper size.
B5 for a B5 paper size.
B6 for a B6 paper size.
B7 for a B7 paper size.
B8 for a B8 paper size.
B9 for a B9 paper size.
ROLL89MM for a 89 MM Roll paper size.
ROLL127MM for a 127 MM Roll paper size.
ROLL100MM for a 100 MM Roll paper size.
ROLL210MM for a 210 MM Roll paper size.
Examples
PICTBRIDGE:PAPERSIZEL sets the paper size to L.
PICTBRIDGE:PAPERSIZE? might return PICTBRIDGE:PAPERSIZE DEFLT
indicating the paper size is set to Default.
PICTBridge:PAPERType
This command specifies the paper type.
Group
PictBridge
Syntax
PICTBridge:PAPERType {DEFLT|PLAIN|PHOTO|FASTPHOTO}
PICTBridge:PAPERType?
Arguments
DEFLT for a default print paper type.
PLAIN for a plain print paper type.
MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual 2-463
Commands Listed in Alphabetical Order
PHOTO for a phot
o print paper type.
FASTPHOTO for a fastphoto print paper type.
Examples
PICTBRIDGE:PAPERTYPE PLAIN sets the paper type to Plain.
PICTBRIDGE:PAPERTYPE? might return PICTBRIDGE:PAPERTYPE DEFLT
indicating the default paper type.
PICTBridge:PRINTQual
This command specifies the output print quality.
Group
PictBridge
Syntax
PICTBridge:PRINTQual {DEFLT|NRMAL|FINE|DRAFT}
PICTBridge:PRINTQual?
Arguments
DEFLT for the default quality print.
NRM
AL
for a normal quality print.
FINE for a fine quality print.
DRAFT for a draft quality print.
Examples
PICTBRIDGE:PRINTQUAL FINE sets the print quality to Fine.
PICTBRIDGE:PRINTQUAL? might return PICTBRIDGE:PRINTQUAL DEFLT
indicating the default quality print.
POWer:CURRENTSOurce
This command specifies the current source for the power application.
Conditions
This command requires a DPO4PWR application module for 4000 series models,
or an MDO3PWR application module for MDO3000 series models.
Group
Power
Syntax
POWer:CURRENTSOurce {CH1|CH2|CH3|CH4|REF1|REF2|REF3|REF4}
POWer:CURRENTSOurce?
2-464 MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual
Commands Listed in Alphabetical Order
Arguments
CH1–CH4 sets an
analog channel as the current source.
REF1–REF4 sets a reference waveform as the current source.
Examples
POWER:CURRENTSOURCE CH1 sets the current source as CH1.
POWER:CURRENTSOURCE? might return POWER:CU RRENTSOURCE CH2 indicating
that CH2 is the current source.
POWer:DISplay
This command controls whether or not to display the power test results. Thisisthe
equivalent to pressing the Test button and then selecting the power application.
The same control is provided for each application.
Conditions
This command requires a DPO4PWR or a MDO3PWR application module.
Group
Power
Syntax
POWer:DISplay {OFF|ON|0 |1}
POWer:DISplay?
Arguments
OFF or 0 turns off the display settings.
ON or 1 turns on the display settings.
Examples
POWER:DISPLAY 1 turns on the display.
POWER:DISPLAY? might return :PO WER:DISPLAY 0 indicating that the display
is off.
POWer:GATESOurce
This command specifies the gate source for the power application.
NOTE. This command is not applicable to 2-channel models. Any attempt to set
the
:GATESOurce
to other than
NONe
will not take effect.
Conditions
This command requires a DPO4PWR application module for 4000 series models,
or an MDO3PWR application module for MDO3000 series models.
MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual 2-465