MDO3000 Programmer Manual.pdf - 第47页

Command Groups T able 2-18: Bus Commands (cont.) Commands Description BUS:B<x>:ETHERnet:SOUrce: DMINus This command speci ﬁ es the Ethernet data source for D- input for single-ended probing. BUS:B<x>:ETHERnet…

Command Groups

Table 2-18: Bus

Commands

Commands Description

BUS? Returns the parameters for each seria l (if installed) and parallel bus.

BUS:B<x>:ARINC429A:BITRate This command speciﬁes the bit rate for the ARINC429 bus.

BUS:B<x>:ARINC429A:DATA:

FORMAT

This command speciﬁes the size of the DATA ﬁeld in an ARINC429 packet.

BUS:B<x>:ARINC429A:POLarity This command sets the ARINC429 bus polarity to normal or inverted.

BUS:B<x>:ARINC429A:SOUrce This command speciﬁes the source for differential input for the ARINC429 bus.

BUS:B<x>:AUD io:BITDelay This command speciﬁes the number of delay bits for the AUDIO bus

BUS:B<x>:AUDio:BITOrder This command speciﬁes the bit order for the AUDIO bus

BUS:B<x>:AUD io:C H A N nel:SIZe This command speciﬁes the number of bits per channel for the AUDIO bus

BUS:B<x>:AUDio:C LOCk:POLarity This command speciﬁes the clock polarity for the A UDIO bus

BUS:B<x>:AUD io:C LOC k:SOUrce This command speciﬁes the clock source waveform for the AUDIO bus

BUS:B<x>:AUDio:DATa:POLarity This command speciﬁes the data polarity for the AUDIO bus

BUS:B<x>:AUDio:DATa:SIZe This command speci ﬁes the number of bits per word for the AUDIO bus

BUS:B<x>:AUDio:DATa:SOUrce This command speciﬁes the data source waveform for the A UDIO bus

BUS:B<x>:AUDio:DISplay:FORMat This command speciﬁes the display format for the AUDIO bus

BUS:B<x>:AUD io:F RAME:SIZe This command speciﬁes the number of channels in each frame for the AUDIO bus

BUS:B<x>:AUDio:FRAMESync:

Larity

This command speciﬁes the frame sync polarity for the AUDIO bus

S:B<x>:AUDio:FRAMESync:

SOUrce

is command speciﬁes the frame sync source waveform for the AUDIO bus

BUS:B<x>:AUDio:TYPe This command speciﬁes the audio format (type) for the AUDIO bus

BUS:B<x>:AUDio:WORDSel:

POLarity

This command speciﬁes the word select polarity for the AUDIO bus

BUS:B<x>:AUDio:W ORDSel:SOUrce This command speciﬁes the word select source waveform for the AUDIO bus

BUS:B<x>:CAN:FD:BITRate This command speciﬁes the bit rate for the data phase of a CAN FD packet

BUS:B<x>:CAN:FD:STANDard This command speciﬁes the CAN FD standard: ISO (11898-1:2015) or non-ISO

(Bosch:2012)

BUS:B<x>:CAN:BIT Rate This command speciﬁes the bit rate for the CAN bus

BUS:B<x>:CAN:PRObe This command speciﬁes the probing method for the CAN bus

BUS:B<x>:CAN:SAMPLEpoint This command speciﬁes the sample point (in %) to sample during each bit period

BUS:B<x>:CAN:STANDard This command speciﬁes CAN or CAN FD bust standard: CAN 2.0 or CAN FD

BUS:B<x>:CAN:SOUrce This command speciﬁ es the C AN bus data source

BUS:B<x>:DISplay:FORMat Sets the display format for the numerical information in the speciﬁed bus waveform

BUS:B<x>:DISplay:TYPe Sets the display type for the speciﬁed bus

BUS:B<x>:ETHERnet:PRObe This command speciﬁes the Ethernet probe type: differential or single-ended.

BUS:B<x>:ETHERnet:PROTOcol Use this command to set the Ethernet protocol type to TCP/IPv4, or to OTHER.

BUS:B<x>:ETHERnet:SOUrce:

DIFFerential

This command speciﬁes the Ethernet data source for differential input.

2-16 MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual

Command Groups

Table 2-18: Bus Commands (cont.)

Commands Description

BUS:B<x>:ETHERnet:SOUrce:

DMINus

This command speciﬁes the Ethernet data source for D- input for single-ended probing.

BUS:B<x>:ETHERnet:SOUrce:

DPLUs

This command speciﬁes the Ethernet data source for the D+ input for single-ended probing.

BUS:B<x>:ETHERnet:TYPe This command speciﬁes the Ethernet standard type: 10Base-T o r 100Base-T.

BUS:B<x>:FLEXray:BITRate This command speciﬁes the bit rate for the FlexRay bus signal

BUS:B<x>:FLEXray:CHannel This command speciﬁes the FlexRay bus ID format

BUS:B<x>:FLEXray:SIGnal This command speciﬁes the FlexRay bus standard

BUS:B<x>:FLEXray:SOUrce This command speciﬁes the FlexRay bus data source

BUS:B<x>:I2C:ADDRess:RWINClude Sets and returns whether the read/write bit is included in the address

BUS:B<x>:I2C{:CLOCk|:SCLk}:

SOUrce

This command speciﬁ es the I2C bus SCLK source

BUS:B<x>:I2C{:DATa|:SDAta}:

SOUrce

This command speciﬁes the I2C bus SDATA source

BUS:B<x>:LABel This command speciﬁes the waveform label for the speciﬁ ed bus

BUS:B<x>:LIN:BITRate This command speciﬁes the bit rate for the LIN bus.

BUS:B<x>:LIN:IDFORmat This command speciﬁ es the LIN bus ID format

BUS:B<x>:LIN:POLarity This command speciﬁes the LIN bus polarity

BUS:B<x>:LIN:SAMPLEpoint This command speciﬁes the point to sample during each bit period, as a percent, for the

LIN bus.

BUS:B<x>:LIN:SOUrce This command speci ﬁes the LIN bus data source

BUS:B<x>:LIN:STANDard This command speciﬁes the LIN bus standard

BUS:B<x>:MIL1553B:POLarity This command sets the MIL-STD-1553 bus polarity to normal or inverted.

BUS:B<x>:MIL1553B:

RESPonsetime:MAXimum

This command speciﬁes the maximum response time to a valid command issued for the

MIL-STD-1553 bus.

BUS:B<x>:MIL1553B:

RESPonsetime:MINimum

This command speciﬁes the minimum response time to a valid command issued for the

MIL-STD-1553 bus.

BUS:B<x>:MIL1553B:SOUrce This command speciﬁes the source for differential input for the MIL-STD-1553 bus.

BUS:B<x>:PARallel:BIT<x>:SOUrce This command speciﬁes the bit source for the parallel bus.

BUS:B<x>:PARallel:CLOCk:EDGE This command speciﬁes the clock edge for the parallel bus

BUS:B<x>:PARallel:CLOCk:

ISCLOCKed

This command speciﬁes the state of the clock function for the parallel bus.

BUS:B<x>:PARallel:CLOCk:SOUrce This command speci ﬁes the clock source waveform for the parallel bus.

BUS:B<x>:PARallel:WIDth This command speciﬁes the number of bits to use for the width of the parallel bus.

BUS:B<x>:POSition This command speciﬁes the position of the bus waveform on the display.

BUS:B<x>:RS232C:BITRate This command speciﬁes the bit rate for the RS-232 bus.

BUS:B<x>:RS232C:DATABits This command speciﬁes the number of bits in the data frame for the RS-232 bus.

BUS:B<x>:RS232C:DELIMiter This command speciﬁes the delimiting value for a packet on the RS-232 bus.

BUS:B<x>:RS232C:DISplaymode This command speciﬁes the display mode for the RS-232 bus (frame or packet).

MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual 2-17

Command Groups

Table 2-18: Bus Commands (cont.)

Commands Description

BUS:B<x>:RS232C:PARity This command speciﬁes parity for the RS-232 bus

BUS:B<x>:RS232C:POLarity This command speciﬁes the polarity for the RS-232C bus

BUS:B<x>:RS232C:RX:SOUrce This command speciﬁes the RX source waveform for the RS-232 bus.

BUS:B<x>:RS232C:TX:SOUrce This command speciﬁes the TX source waveform for the RS-232 bus.

BUS:B<x>:SPI:BITOrder This command speciﬁes the bit order for the SPI bus

BUS:B<x>:SPI{:CLOCk|:SCLk}:

POLarity

This command speciﬁes the SCLK polarity for the SPI bus.

BUS:B<x>:SPI{:CLOCk|:SCLk}:

SOUrce

This command speciﬁes the SCLK source for the SPI bus.

BUS:B<x>:SPI:DATa{:IN|:MISO}:

POLarity

This command speciﬁes the MISO polarity for the SPI bus.

BUS:B<x>:SPI:DATa{:IN|:MISO}:

SOUrce

This command speciﬁes the MISO source for the SPI bus.

BUS:B<x>:SPI:DATa{:OUT|:MOSI}:

POLarity

This command speciﬁes the MOSI polarity for the SPI bus.

BUS:B<x>:SPI:DATa{:OUT|:MOSI}:

SOUrce

This command speciﬁes the MOSI s ource for the SPI bus.

BUS:B<x>:SPI:DATa:S IZe This command speciﬁ es the number of bits per word (data size) for the speciﬁed SPI bus.

BUS:B<x>:SPI:FRAMING This command speciﬁes the type of framing to use for the SPI bus.

BUS:B<x>:SPI:IDLETime This command speciﬁes the idle time, in seconds, for the SPI bus.

BUS:B<x>:SPI{:SELect|:SS}:

POLarity

This command speciﬁes the polarity for the SPI bus.

BUS:B<x>:SPI{:SELect|:SS}:SOUrce This command speciﬁes the source waveform for the SPI bus.

BUS:B<x>:STATE This command speciﬁ es the on/off state of the bus.

BUS:B<x>:TYPe This command speciﬁes the bus type

BUS:B<x>:USB :BITR a te This command speciﬁes the bit rate for the USB bus.

BUS:B<x>:USB:PRObe This command speciﬁes the type of probe connected to the USB bus.

BUS:B<x>:USB:SOUrce:DIFFerential This command speciﬁes the source waveform for the eUSB bus when using a differential

probe.

BUS:B<x>:USB:SOUrce:DMINus This command speci ﬁes the source waveform for the USB bus D- input.

BUS:B<x>:USB:SOUrce:DPLUs This command speciﬁes the source for the USB D+ input.

BUS:LOWerthreshold:CH<x> This command speciﬁes the lower threshold for each channel.

BUS:LOWerthreshold{:MATH|:

MATH1}

This command speciﬁes the lower threshold for the math w aveform.

BUS:LOWerthreshold:REF<x> This command sets the lower threshold for each reference waveform.

BUS:THReshold:CH<x> This command speciﬁes the threshold for a channel.

BUS:THReshold:D<x> This command speciﬁes the threshold for a digital channel.

BUS:UPPerthreshold:CH<x> This command speciﬁes the upper threshold for each channel.

2-18 MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual