00197490-03_SM_CP20-P-M2_EN保养维护.pdf - 第29页

4 Component camera, Z axis and component sensor 4.2 Replacing the Z axis cover Service Manual SIPLACE SpeedStar (C&P20 P / C&P20 M2) 03/2018 29 4.2 Replacing the Z axis cover CAUTION Sensitive lenses The transmit…

100%1 / 88
4 Component camera, Z axis and component sensor
4.1 Replacing the component camera
28 Service Manual SIPLACE SpeedStar (C&P20 P / C&P20 M2) 03/2018
4.1.1 Board: LED driver BE VHS
The "LED driver BE VHS" board [03003002‑xx] is fitted in the following component cameras:
●
Component camera C&P (type23) 6x6 digital [03003426‑xx]
●
Component camera C&P (type41) 6x6 digital [03078957‑xx]
●
Component camera C&P (type43) 6x6 Hotlink [03122243‑xx]
Fig.26: 03003002-04
LEDs [03003002-04]
LED Color Status Signal name Description
D1 GN ON 40V_IN +40VDC operating voltage
D3 GN ON 15V+ +15VDC operating voltage
D4 GN ON 15V- -15VDC operating voltage
D5 GN ON 5V+ +5VDC operating voltage
4 Component camera, Z axis and component sensor
4.2 Replacing the Z axis cover
Service Manual SIPLACE SpeedStar (C&P20 P / C&P20 M2) 03/2018 29
4.2 Replacing the Z axis cover
CAUTION
Sensitive lenses
The transmitter and receiver unit lenses on the component sensor are highly sensitive.
► Make sure that you do not damage or contaminate the lens system.
Parts
●
Bottom cover assembly for SIPLACE C&P20P [03093482Sxx]
Overview
Fig.27: Z axis cover
1 Z axis cover on the SIPLACE C&P20P 2 Fastening screw
(ISO4762‑M3x35‑A2‑70)
Washer (ISO7089-3-200HV-A2)
3 Fastening screw
(ISO4762‑M2.5x4‑A2‑70)
4 Two fastening screws on raceway
(ISO4762‑M2.5x4‑A2‑70)
Preparation
► Remove the head from the machine. For details about removing and fitting the placement
head, refer to the service manual for your machine.
Fit the head on the head mount [03056231‑xx].
4 Component camera, Z axis and component sensor
4.2 Replacing the Z axis cover
30 Service Manual SIPLACE SpeedStar (C&P20 P / C&P20 M2) 03/2018
Removal
Fig.28: Fastening screws
► Remove the four fastening screws(2) to(5) and
then take the Z axis cover(1) off.
Installation
► Follow the removal instructions in reverse order for installation. Also observe the following
instructions:
Fig.29: Torques for fastening screws used for Z axis cover
1. Z axis cover
2. Cylinder head screw with hexagon socket head
caps ISO4762-M2.5x4-A2-70 [03042531‑xx]
No torque
3. Cylinder head screw with hexagon socket head
caps ISO4762-M3x35-A2-70 [03043114‑xx]
Torque: 1.3Nm
4. Cylinder head screw with hexagon socket head
caps ISO4762-M2.5x4-A2-70 [03042531‑xx]
Torque: 0.6Nm
5. Cylinder head screw with hexagon socket head
caps ISO4762-M2.5x4-A2-70 [03042531‑xx]
Torque: 0.6Nm
Fig.30: Check
► Check that the Z axis is moving without touching
the cover.