00197490-03_SM_CP20-P-M2_EN保养维护.pdf - 第5页

1 Introduction 1.1 Safety instructions Service Manual SIPLACE SpeedStar (C&P20 P / C&P20 M2) 03/2018 5 1 Introduction This document is a manual or reference work for performing service work on the SIPLACE® C&…

100%1 / 88
4 Service Manual SIPLACE SpeedStar (C&P20 P / C&P20 M2) 03/2018
Contents
6 Pressure control valve (PRV).. 47
6.1 Replacing the PRV.. 47
6.2 Replacing the membrane and other small parts on the PRV.. 49
6.3 Replacing the exhaust tube.. 59
6.4 Calibrating the digital PRV.. 60
6.4.1 Zero point calibration of pressure control valve.. 60
7 Holding circuit, aperture ring and silencer.. 61
7.1 Replacing the holding circuit/reflecting ring.. 61
7.2 Replacing the seal disk on the aperture ring/holding circuit.. 68
7.3 Replacing the silencer (venturi mode only).. 68
7.4 Vacuum sensor holding circuit board for SIPLACE C&P20P.. 69
8 Return unit and return cylinder.. 71
8.1 Replacing the return unit.. 71
8.2 Replacing the return cylinder or return cylinder holder.. 74
8.3 Replacing the driver lever.. 75
9 Intermediate distributor.. 77
9.1 Replacing the intermediate distributor board.. 77
9.1.1 Intermediate distributor board for SIPLACE C&P20P [03110751-xx].. 79
10 Miscellaneous.. 81
10.1 Replacing the handle.. 81
11 Software functions.. 83
11.1 Zero point correction for the Star and Z axis.. 83
11.1.1 Transfer head specific data to the machine data after manual head exchange.. 83
11.2 Calibration.. 84
11.2.1 Calibrating the heads and cameras (SW70x).. 84
11.2.2 Calibration procedure.. 85
11.3 Transferring the head specific data (from SW701).. 86
1 Introduction
1.1 Safety instructions
Service Manual SIPLACE SpeedStar (C&P20 P / C&P20 M2) 03/2018 5
1 Introduction
This document is a manual or reference work for performing service work on the SIPLACE®
C&P20 P and C&P20 M2 placement head types.
1.1 Safety instructions
DANGER
Nonobservance of these safety instructions may cause injury to personnel and dam-
age to the machine!
► Please observe the safety instructions in the user manual of the relevant machine
for all work!
1.1.1 Conventions for the use of safety instructions and symbols
Safety Information
This manual contains notes that must be observed to guarantee your personal safety and to avoid
damage to equipment. These notes are highlighted by warning triangles and are indicated as fol-
lows according to the level of risk:
DANGER
Definition
For the purposes of this manual, this indicates that fatal or severe injuries or considerable
damage to property will occur if this hazard warning is not observed.
WARNING
Definition
For the purposes of this manual, this indicates that fatal or severe injuries or considerable
damage to equipment may occur if these warning instructions are not followed.
CAUTION
Definition
For the purposes of this manual, this indicates that minor injuries or damage to property
may occur if this caution is not observed.
NOTICE
Definition
For the purposes of this manual, this note provides information about the product or indic-
ates a part of the manual that requires particular attention.
Symbols
Example Description
Next This typeface marks controls and interface elements in the software.
► These symbol indicates actions that have to be performed by the operator.
1.1.2 Safety instructions on hazardous materials
CAUTION
Observe the safety data sheets
Observe the applicable safety data sheet, when handling hazardous materials (e. g. Loctite
241, ethanol).
1 Introduction
1.2 Other instructions
6 Service Manual SIPLACE SpeedStar (C&P20 P / C&P20 M2) 03/2018
1.1.3 Safety instructions for the component sensor
Fig.1: Component sensor protective cap [03112729‑xx]
 WARNING!
Prisms on the component sensor
The component sensor prisms, underneath the
placement head, are easily damaged.
Never place the placement head down on the
component sensor.
For all work, fit the protective cap [03112729‑xx]
onto the component sensor of the placement
head.
.
1.2 Other instructions
1.2.1 Environmentally-friendly disposal of materials and components
Our products are manufactured using only materials and parts that can be easily separated and
disposed of in an environmentally-friendly way.
NOTICE
Observe the applicable regulations
The company operating the system has sole responsibility for the proper, environmentally-
friendly disposal of machines, working materials, consumable materials and wear parts.
► Please observe your national statutory provisions for waste disposal and environ-
mental protection.
1.2.2 Use of original accessories and spare parts
Only use original spare parts and authorized accessories. The use of other parts will affect safety
and will invalidate the liability for any consequential damage.
1.2.3 Information about this service manual
WARNING
Additional qualifications required
The service work described in this manual may only be performed by specially trained ser-
vice technicians, with appropriate qualifications and expertise.
If you should have any questions during the service work, please contact the SIPLACE customer
hotline directly or send an e-mail to hotline.siplace@asmpt.com.