00197490-03_SM_CP20-P-M2_EN保养维护.pdf - 第78页
9 Intermediate distributor 9.1 Replacing the intermediate distributor board 78 Service Manual SIPLACE SpeedStar (C&P20 P / C&P20 M2) 03/2018 Removal Fig.120: Pulling the cover off ► Pull the cover (1) off the i…
9 Intermediate distributor
9.1 Replacing the intermediate distributor board
Service Manual SIPLACE SpeedStar (C&P20 P / C&P20 M2) 03/2018 77
9 Intermediate distributor
9.1 Replacing the intermediate distributor board
Parts
●
For SIPLACE C&P20P: intermediate distributor board assembly SIPLACE C&P20P
[03110751Sxx]
●
For SIPLACE C&P20M2: intermediate distributor assembly SIPLACE C&P20M2
[03124689Sxx]
Overview
Fig.118: Overview of intermediate distributor 1
1. Intermediate distributor board assembly
SIPLACE C&P20P [03110751-xx]
2. Four fastening bolts
Fig.119: Overview of intermediate distributor 2
Intermediate distributor board assembly SIPLACE
C&P20P [03110751-xx]
Preparation
► Although this work can be performed in the machine, you might find it advisable to remove the
head so that you have better access to it.
For details about removing and fitting the placement head, refer to the service manual for your
machine.
In this case, fit the head on the head mount [03056231‑xx].
► Make sure that the component sensor protective cap is fitted when outside the machine.
9 Intermediate distributor
9.1 Replacing the intermediate distributor board
78 Service Manual SIPLACE SpeedStar (C&P20 P / C&P20 M2) 03/2018
Removal
Fig.120: Pulling the cover off
► Pull the cover(1) off the intermediate distributor.
The cover is fixed by four press studs on the stay
bolts.
NOTICE!
Older heads may not have this cover yet.
.
Fig.121: Dismantling the intermediate distributor board
► Unplug all electrical connections. Mark their posi-
tions to make clear assignment easier later on.
Take particular care not to confuse the two board
connectors(1).
► Remove the four screws fastening the intermedi-
ate distributor and then take off the intermediate
distributor.
Installation
► Follow the removal instructions in reverse order for installation. Also observe the following
instructions:
NOTICE
Installation instructions
Transfer the machine data to the EPROM!
► Transfer the machine data from the station to the intermediate distributor. For more in-
formation about this read section 11.3 "Transferring the head specific data (from
SW701)" [}86].
9 Intermediate distributor
9.1 Replacing the intermediate distributor board
Service Manual SIPLACE SpeedStar (C&P20 P / C&P20 M2) 03/2018 79
9.1.1 Intermediate distributor board for SIPLACE C&P20P [03110751-xx]
Fig.122: Intermediate distributor board for SIPLACE C&P20P
Connector
X1,X
2
Flat ribbon cable to the head adapter X3 Power supply for star motor
X8 Power supply for Z axis X15 Valve for return unit
X16 CAN bus X16b CAN bus
X17 Z axis light barrier down X19 Board for holding circuit vacuum sensor
X20 Power supply for ED distributor X21 Diagnosis connector
X22 Incremental star X23 Incremental Z axis
X24 Fan X25 Digital pressure control valve
X26 Component sensor
LEDs
H1 Fan Yellow
H2 Fan error Red
H5 +5 V Green
H6 +15 V Green
H8 +24 V Green
H9 Error 24 V DP Red
H11 24 V DP ON Yellow
H12 Return cylinder ON Yellow
H13 Status of pressure control valve Yellow
DIP switches
S1 DP Power ON 1-4 OFF
S1 Z down test 2-3 OFF