00193897-0302_AI_MTC2+BE_DE+EN.pdf - 第78页
Assembly instructions MTC2 and Component docking unit on SIPLACE HF and X-se ries Edition 07/2009 76 2.4 Part s used 2.4.1 Hardware: (001 1 6438-) SIPLACE Matrix T ray Changer 2 (MTC2) –M T C 2 2 1 x 03009963-03 Slide-in…
Assembly instructions MTC2 and Component docking unit on SIPLACE HF and X-series
Edition 07/2009
75
2.3 Safety instructions
WARNING 2
Comply with the higher ranking "Safety Instructions" in Chapter "Operational Safety" in the User
Manual and Service Manual. 2
The placement machines SIPLACE are powered by mains voltage.
Portions of the system are therefore conducting da
ngerous electricity, inside the machine even
while the master switch is turned off.
Death, serious injury or considerable damage may result if these automatic placement systems
a
re handled incorrectly.
After you have properly carried out the shut-
down of the operating system:
Before all work the machine must be turned off at the
main switch and isolated from the mains. In
addition, the compressed air supply must be turned off at the main valve of the compressed air
unit in the machine base and the compressed air lines must be bled by actuating the needle valve
at the compressed air unit.
Danger: For anyone wearing a heart pacemaker it is not permitted to work near linear motors, as
d
escribed in detail in the User Manual and the Service Manual, Chapter "Special Safety Instruc-
tions when working in vivinty of powerful magnetic fields" .
Obey the applicable accident prevention regulations, DIN
standards and special safety codes of
your country at all times. DIN EN 60204 must be adhered to during all work inside the machine
base.
Follow the instructions regarding residual voltages in Chapter "Operational Safety".
Comply with regulations on ESDs (see Chapter "Operational Safety").
During the work of retrofitting secure the machine conscientiously against other personnel and
p
revent it from being turned back on without authorization, as described in the User Manual in the
chapter "Locking the Machine...".
There is additional, higher risk of accident when working with the SITEST program.
The SITEST program is only to be started by personnel who are authorized to do so. 2
2
2.3.1 Definitions
2
Please note
2
2
2
Caution
2
Assembly instructions MTC2 and Component docking unit on SIPLACE HF and X-series
Edition 07/2009
76
2.4 Parts used
2.4.1 Hardware: (00116438-) SIPLACE Matrix Tray Changer 2 (MTC2)
–MTC2 2
1 x 03009963-03 Slide-in framework 2
1 x 03012584-xx Angle plate 2
1 x 03021281-xx Protection HF R MTC-pane cpl. 2
1 x 03015947-xx Protection X-HS R pane locking 2
1 x 03012599-xx Cover right 2
1 x 03012600-xx Cover left 2
1 x 03011592-xx Blind plug 2
2 x 03012601-xx Tank 2
1 x 03048626-xx Pane shortened for MTC cpl. 2
3 x 00066135-xx Polybag 160 * 220 mm 2
1 x 03014445-xx Jumper cable sensor input 2
1 x 03027905-xx Adapter cable CAN bus MTC2 2
14 x 03013056-xx ISO 7380-M5xx12-10.9 black chrome 2
4 x 00305521-xx DIN EN ISO 7380 M5x8 - 10.9 2
2 x 00845078-xx DIN912 M8x30 - 8.8 2
3 x 00319507-xx DIN912 M8x130 - 8.8 2
3 x 00353338-xx Bridge circuit grey 280-402 2
1 x 03053370-xx Machine facing cover sheet cpl. MTC 2
1 x 00193897-xx Assem. Inst. MTC2 - Comp. Table HF-/X-series 2
2.4.2 Hardware: Component docking unit HF for S-tape feeders
(for HF-series, Series No. up to A001)
00119622-xx Component trolley SIPLACE HF / X-series / D3 (S tape feeder) 2
00377312-xx Retrofit kit Interface component trolley HF (up to A001) left 2
1 x 00376124-xx Component docking unit location 1/3 left 2
1 x 03004716-xx Wasteþchute cpl. 2
Assembly instructions MTC2 and Component docking unit on SIPLACE HF and X-series
Edition 07/2009
77
1 x 03003719-xx Tank 2
1 x 03004714-xx Protective cover_right cpl. 2
1 x 03006390-xx Mounting parts EGS cover plate 3 2
1 x 03005290-xx EGS centre right 2
1 x 03005372-xx Cover long EGS centre 2
1 x 03001910-xx Inner sliding strips 2
5 x 00323157-xx DIN 7991 M6x16 - 8.8 2
2 x 00845076-xx DIN912 M8x20 - 8.8 2
2 x 00845080-xx DIN912 M8x40 - 8.8 2
2 x 00308873-xx DIN912 M8x55 - 8.8, copper-plated / nickel-plated 2
1 x 03002681-xx Reamed bolt 10*40/M8 2
1 x 00193897-xx Assembly instructions MTC2 - Component trolley for HF-/X-series 2
00377313-xx Retrofit kit Interface component trolley HF (up to A001) right 2
1 x 00376125-xx Component docking unit location 2/4 right 2
1 x 03004716-xx Wasteþchute cpl. 2
1 x 03003719-xx Tank 2
1 x 03004714-xx Protective cover_right cpl. 2
1 x 03006390-xx Mounting parts EGS cover plate 3 2
1 x 03005290-xx EGS centre right 2
1 x 03005372-xx Cover long EGS centre 2
1 x 03001910-xx Inner sliding strips 2
5 x 00323157-xx DIN 7991 M6x16 - 8.8 2
2 x 00845076-xx DIN912 M8x20 - 8.8 2
2 x 00845080-xx DIN912 M8x40 - 8.8 2
2 x 00308873-xx DIN912 M8x55 - 8.8, copper-plated / nickel-plated 2
1 x 03002681-xx Reamed bolt 10*40/M8 2
1 x 00193897-xx Assembly instructions MTC2 - Component trolley for HF- / X-series 2