OM-1058-002.pdf - 第47页
Tg0409-PM-SO 0410-002 46 5.3 Maintenance Method • For tape feeders of 12 mm width or more (Including TF-0814) T able 8-1 Fig. 74 Shutter Driving Pin (Fig. 80) T ape Feed Link Assembly Fulcrum Pin (Fig. 80) Pitch Selectin…
Tg0409-PM-SO
5.3.4 Monthly Maintenance
0410-002 45
5.3 Maintenance Method
Fig. 73
Take-up Reel Feed Spring (Fig. 75)
Feed Lever Fulcrum Pin (Fig. 75)
Fulcrum Pin Sliding Section of Tape Take-up Link (Fig. 76)
Slack Link Selection Section (Fig. 76)
Tape Feed Link Assembly Fulcrum Section (Fig. 77)
Pick-up Position Adjustment Section (Fig. 77)
Suppressor Holding Lever Fulcrum Pin (Fig. 77)
Transfer Claw Fulcrum Section (Fig. 77)
Shutter Sliding Guide (Fig. 84)
Take-up Reel Feed Roller (Fig. 82)
Locating Lever Fulcrum Section (Fig. 81)
Overrun Stopper Fulcrum Pin (Fig. 78)
Locating Notch Fulcrum Pin (Fig. 78)
Overrun Stopper (Fig. 78)
Pick-up Position Adjustment Pin (Fig. 79)
Shutter Driving Pin (Fig. 79)
Tape Feed Link Assembly Fulcrum Pin (Fig. 79)
Tape Feed Spring (Fig. 81)
Tg0409-PM-SO0410-002 46
5.3 Maintenance Method
• For tape feeders of 12 mm width or more (Including TF-0814)
Table 8-1
Fig. 74
Shutter Driving Pin (Fig. 80)
Tape Feed Link Assembly Fulcrum Pin (Fig. 80)
Pitch Selecting Section on Swing Arm (Fig. 80)
Tape Feed Spring (Fig. 81)
Tape Take-up Link Selection Section (Fig. 83)
Fulcrum Pin of Tape Take-up Link (Fig. 83)
Fig. 75
Fig. 76
Fig. 77
Take-up Reel Feed Spring
Suppressor Holding Lever
Fulcrum Pin
Slack Link Selection Section
Feed Lever Fulcrum Pin
Fulcrum Pin Sliding Section of
Tape Take-up Link
Fig. 75
Fig. 76
Tape Feed Link Assembly
Fulcrum Section,
Pick-up Position Adjustment
Section
Fig. 77
Fig. 77
Transfer Claw Fulcrum Section
Lubrication
Lubrication
Lubrication
Lubrication
Lubrication
Lubrication
Lubrication
Thin Bar
NEW MOLYNOC GREASE No.1
Thin Bar
NEW MOLYNOC GREASE No.1
Thin Bar
NEW MOLYNOC GREASE No.1
Thin Bar
NEW MOLYNOC GREASE No.1
Thin Bar
NEW MOLYNOC GREASE No.1
Thin Bar
NEW MOLYNOC GREASE No.1
Thin Bar
NEW MOLYNOC GREASE No.1
Reference
Drawing
Work Working Tools
Name
Location to be maintained
Check
Tg0409-PM-SO
Table 8-2
0410-002 47
5.3 Maintenance Method
(a) If too much grease is applied, wipe clean with a rag, etc., after
greasing.
(b) After each section has been greased, press the feed lever (for tape
feeders of 12 mm width or more, the feed lever on the feeder set
jig). Press several times to ensure a smooth coating.
(c) These are the locations to be maintained for tape feeders of 12 mm
width or more.
Note
Fig. 78
Fig. 79
Fig. 79
Fig. 80
Fig. 81
Fig. 81
Overrun Stopper Fulcrum Pin
Shutter Driving Pin
Pick-up Position Adjustment Pin
Tape Feed Link Assembly
Fulcrum Pin (Note c)
Tape Feed Spring
Locating Lever Fulcrum Section
Locating Notch Fulcrum Pin
Overrun Stopper
Fig. 78
Fig. 78
Tape Feed Link Assembly
Fulcrum Pin
Fig. 79
Fig. 80
Shutter Driving Pin
(Note c)
Lubrication
Lubrication
Lubrication
Lubrication
Lubrication
Lubrication
Lubrication
Lubrication
Lubrication
Lubrication
Thin Bar
NEW MOLYNOC GREASE No.1
Thin Bar
NEW MOLYNOC GREASE No.1
Thin Bar
NEW MOLYNOC GREASE No.1
Thin Bar
NEW MOLYNOC GREASE No.1
Thin Bar
NEW MOLYNOC GREASE No.1
Thin Bar
NEW MOLYNOC GREASE No.1
Thin Bar
NEW MOLYNOC GREASE No.1
Thin Bar
NEW MOLYNOC GREASE No.1
Thin Bar
NEW MOLYNOC GREASE No.1
Thin Bar
NEW MOLYNOC GREASE No.1
Reference
Drawing
Work Working Tools
Name
Location to be maintained
Check
Fig. 82Take-up Reel Feed Roller Lubrication Thin Bar
NEW MOLYNOC GREASE No.1
Fig. 83
Fig. 83
Tape Take-up Link Selection
Section
Fulcrum Pin of Tape Take-up
Link
Lubrication
Lubrication
Thin Bar
NEW MOLYNOC GREASE No.1
Thin Bar
NEW MOLYNOC GREASE No.1
Fig. 84Shutter Sliding Guide Alcohol, Air Gun, Thin Bar
DAPHNE EPONEX GREASE No. 1
Lubrication
Fig. 80Pitch Selecting Section on
Swing Arm (Note c)
Lubrication Thin Bar
NEW MOLYNOC GREASE No.1