OM-1058-002.pdf - 第49页
Tg0409-PM-SO Fig. 75 (a) Apply grease on the section of . (b) Apply grease from the front and the side (two locations). 0410-002 48 5.3 Maintenance Method Note Front View Side View T ape Feeder of 8 mm Width (except for …
Tg0409-PM-SO
Table 8-2
0410-002 47
5.3 Maintenance Method
(a) If too much grease is applied, wipe clean with a rag, etc., after
greasing.
(b) After each section has been greased, press the feed lever (for tape
feeders of 12 mm width or more, the feed lever on the feeder set
jig). Press several times to ensure a smooth coating.
(c) These are the locations to be maintained for tape feeders of 12 mm
width or more.
Note
Fig. 78
Fig. 79
Fig. 79
Fig. 80
Fig. 81
Fig. 81
Overrun Stopper Fulcrum Pin
Shutter Driving Pin
Pick-up Position Adjustment Pin
Tape Feed Link Assembly
Fulcrum Pin (Note c)
Tape Feed Spring
Locating Lever Fulcrum Section
Locating Notch Fulcrum Pin
Overrun Stopper
Fig. 78
Fig. 78
Tape Feed Link Assembly
Fulcrum Pin
Fig. 79
Fig. 80
Shutter Driving Pin
(Note c)
Lubrication
Lubrication
Lubrication
Lubrication
Lubrication
Lubrication
Lubrication
Lubrication
Lubrication
Lubrication
Thin Bar
NEW MOLYNOC GREASE No.1
Thin Bar
NEW MOLYNOC GREASE No.1
Thin Bar
NEW MOLYNOC GREASE No.1
Thin Bar
NEW MOLYNOC GREASE No.1
Thin Bar
NEW MOLYNOC GREASE No.1
Thin Bar
NEW MOLYNOC GREASE No.1
Thin Bar
NEW MOLYNOC GREASE No.1
Thin Bar
NEW MOLYNOC GREASE No.1
Thin Bar
NEW MOLYNOC GREASE No.1
Thin Bar
NEW MOLYNOC GREASE No.1
Reference
Drawing
Work Working Tools
Name
Location to be maintained
Check
Fig. 82Take-up Reel Feed Roller Lubrication Thin Bar
NEW MOLYNOC GREASE No.1
Fig. 83
Fig. 83
Tape Take-up Link Selection
Section
Fulcrum Pin of Tape Take-up
Link
Lubrication
Lubrication
Thin Bar
NEW MOLYNOC GREASE No.1
Thin Bar
NEW MOLYNOC GREASE No.1
Fig. 84Shutter Sliding Guide Alcohol, Air Gun, Thin Bar
DAPHNE EPONEX GREASE No. 1
Lubrication
Fig. 80Pitch Selecting Section on
Swing Arm (Note c)
Lubrication Thin Bar
NEW MOLYNOC GREASE No.1
Tg0409-PM-SO
Fig. 75
(a) Apply grease on the section of .
(b) Apply grease from the front and the side (two locations).
0410-002 48
5.3 Maintenance Method
Note
Front View Side View
Tape Feeder of 8 mm Width
(except for TF-0814)
Tape Feeders of
12 mm Width or more
(Including TF-0814)
Tape Feeder of 8 mm Width
(Note b)
Tape Feeders of 12 mm Width or more
(Note b)
Front View Side View
Take-up Reel Feed Spring
Every month Lubrication
Apply New Molynoc Grease No. 1 with a thin
bar.
Feed Lever Fulcrum Pin
Every month Lubrication
Apply New Molynoc Grease No. 1 with a thin
bar.
Tg0409-PM-SO
Fig. 76
0410-002 49
Apply grease on the section of .
5.3 Maintenance Method
• For tape feeders of 12 mm width or more
Note
Take-up Reel Socket
Take-up Reel Feed Spring
On the other side
Sliding Section
Fulcrum Pin Sliding Section of Tape
Take-up Link (Including TF-0814)
Every month Lubrication
Work it using the following procedure.
1. Remove the take-up reel socket and take-up
reel feed spring, in that order.
2. Remove the sliding section of the tape
take-up link from the feed lever.
3. Apply New Molynoc Grease No. 1 where
needed, using a thin bar.
4. Attach the sliding section of the tape take-up
link to the feed lever.
5. Attach the take-up reel feed spring and the
take-up reel socket, in that order.
Slack Link Selection Section
Every month Lubrication
Remove the slack link, apply New Molynoc
Grease No. 1 with a thin bar.
Do not apply grease where it is
not necessary, dust or fibers might
adhere there and so might cause
a pick-up error.
Notice