Maintenance Reference(CP45FV) Eng.pdf - 第57页
Lubricant Method 4-1 Chapter 4. Lubricant Method 4.1. Lubrication T able 4-1. T able of Component Lubrication Major Category Sub Category Lubricant T ype Maker Method Period L/M Guide RE-Lubrication SET MNW Schneeberger …
Samsung Component Placer CP45FV Series Maintenance Reference
Caution
Since the lubrication and grease application for the
machine is critical to the lifetime of the machine, ensure
that periodical lubrication and grease application are
performed.
3-18
Lubricant Method
4-1
Chapter 4. Lubricant Method
4.1. Lubrication
Table 4-1. Table of Component Lubrication
Major Category Sub Category Lubricant Type Maker Method Period
L/M Guide
RE-Lubrication
SET MNW
Schneeberger
Grease
Gun
Every Four Months
Head
Ball Spline
ALVANIA
EP GREASE 2
SHELL
Apply
Grease
Every Three
Months
L/M Guide
Grease(EP2)
SHELL
Apply
Grease
Every Month
X-axis
Ball Screw
Grease(G-142K) Kanto Kasei
Apply
Grease
Every Month
Grease(EP2)
SHELL
Grease
Gun
Every Three
Months
L/M Guide
Grease(EP2)
SHELL
Apply
Grease
Every Month
Grease(G-142K)
Kanto Kasei
Grease
Gun
Every Three
Months
Y-axis
Ball Screw
Grease(G-142K)
Kanto Kasei
Apply
Grease
Every Month
Lead Screw
Grease(G-142K)
Kanto Kasei
Apply
Grease
Every Two Months
L/M Guide Rail
Grease(EP2)
SHELL
Apply
Grease
Every Six Months
Conveyor
Width
Adjustment
Chain
Grease(EP2)
SHELL
Apply
Grease
Every Years
Grease(EP2): Li Compl. soap grease no.2(SHELL).
Samsung Component Placer CP45FV Series Maintenance Guide
Grease specifications (EP2, G-142K)
Type : Lithium soap, high load (industrial purpose), lithium complex, and non leaded
Cone Penetration: 265-295 (NLGI Grade No. 2), Temperature range: -15 / +150 ℃
(Dropping point: 255℃)
Purchase information: Kihung Trading Co. (KANTO KASEI Sales representative in
Busan (T.051-808-3549)).
Available in the unit of 15kg(1 mal).
Application method
In principle, apply or inject once every 100km of operation.
Inject or apply once every 1~2 weeks (If the machine is operated 24 hours a day)
Inject or apply once a month (If the machine is operated 10 hours a day)
Injection method
Check the grease gun. Do not mix it with other grease.
Inject through the grease nipple by using the Grease Gun. (Recommended injection
amount: 5g / per injection for one block)
Inject grease while moving the gantry slowly as it might not reach the rolling bearing
if it is injected while the LM Block is stationary. (Y axis)
Check the grease injection status while operating the machine slowly by using the
Teaching Box.
For even application of grease, warm up the machine for 1 minute before application.
How to apply grease
First, remove any dust or contaminant with antidust cloth, and apply the grease thinly on
the surface of the rail and screw groove with a brush. Then slowly move the axis twice or
three times to remove any excessive grease on the rail and both ends of the screw.
If there is a lot of dust in the environment, it is best to remove chips or dust on the rail
thoroughly and apply grease often even before the regular grease lubrication period.
Recommended brush Type : The brush for paint coating (hog or horse hair brush)
Recommended grease application amount: 1cc/application for one block
Pyoundo Paint Brush Paint Brush For Painting
Grease storage method
A grease container must be opened in a clean environment devoid of dust.
Caution
4-2