SOM-2079-001_w.pdf - 第146页

143 SOM-2079 異常 ID 異常名、説明、要因および復帰方法 601f09 NL Axis offset teach An error occurred in the teaching operation. ----- 602001 Auto. Teaching Mode in Auto.Opn A recog error occurred during teaching operation.(Back) (This prob…

100%1 / 179
142
SOM-2079
異常 ID 異常名、説明、要因および復帰方法
601d01 Library teaching
Abnormality was found in the division recognition position movement when the
library was taught.
Please make a new library instruction again.
601e01 Board height measurement teach
Recognition mark is abnormal
Please carry out remaining teach after having manual alignment.
601e02 Board height measurement teach
Abnormality occurred during board height measurement teach movement.
-----
601e03 Board height measurement teach
Failed teaching: The measurement is wrong.
Clean the surface of the jig.
601e04 Board height measurement teach
Failed Teaching: The jig is tilting.
Reposition it with the P.C.B. thickness reviewed.
601e05 Board height measurement teach
Failed Teaching: Jig Recognition Error
Check the condition in locating the jig P.C.B.
601f01 NL Axis offset teach
Linear measure was found abnormality while measuring.
-----
601f02 NL Axis offset teach
The result of the linear measure sensor is out of the tolerance.
-----
601f03 NL Axis offset teach
An error for the NS axis movement occurred.
-----
601f04 NL Axis offset teach
Time out of the NS axis movement occurred.
-----
601f05 NL Axis offset teach
An error for the DD axis movement occurred.
-----
601f06 NL Axis offset teach
Time out of the DD axis movement occurred.
-----
601f07 NL Axis offset teach
An error for the NL axis movement occurred.
-----
601f08 NL Axis offset teach
Time out of the NL axis movement occurred.
-----
1005-001
6.14 自動教示
143
SOM-2079
異常 ID 異常名、説明、要因および復帰方法
601f09 NL Axis offset teach
An error occurred in the teaching operation.
-----
602001 Auto. Teaching Mode in Auto.Opn
A recog error occurred during teaching operation.(Back) (This problem may be
caused by the teaching jig unset or dirty.)
Check that the teaching jig is set properly on the position, or clean the teaching
jig.
602002 Auto. Teaching Mode in Auto.Opn
A recog error occurred during teaching operation.(Front) (This problem may be
caused by the teaching jig unset or dirty.)
Check that the teaching jig is set properly on the position, or clean the teaching
jig.
602003 Auto. Teaching Mode in Auto.Opn
An error occurred during teaching. (Rear)
-----
602004 Auto. Teaching Mode in Auto.Opn
An error occurred during teaching. (Front)
-----
602005 Auto. Teaching Mode in Auto.Opn
An error for timeout occurred during teaching. (Rear)
-----
602006 Auto. Teaching Mode in Auto.Opn
An error for timeout occurred during teaching. (Front)
-----
602007 Auto. Teaching Mode in Auto.Opn
An error occurred during teaching. (Rear) (Operation timeout in the Beam Offset
Teaching)
-----
602008 Auto. Teaching Mode in Auto.Opn
An error occurred during teaching. (Front) (Operation timeout in the Beam Offset
Teaching)
-----
602009 Auto. Teaching Mode in Auto.Opn
An error occurred during teaching. (Rear) (Operation error in the Beam Offset
Teaching)
-----
60200a Auto. Teaching Mode in Auto.Opn
An error occurred during teaching. (Front) (Operation error in the Beam Offset
Teaching)
-----
60200b Auto. Teaching Mode in Auto.Opn
A
n
error occurred during teaching. (Rear) (Operation timeout in the Head Rotation
Center Offset Teaching)
-----
1005-001
6.14 自動教示
144
SOM-2079
異常 ID 異常名、説明、要因および復帰方法
60200c Auto. Teaching Mode in Auto.Opn
An error occurred during teaching. (Front) (Operation timeout in the Head
Rotation Center Offset Teaching)
-----
60200d Auto. Teaching Mode in Auto.Opn
An error occurred during teaching. (Rear) (Operation error in the Head Rotation
Center Offset Teaching)
Check that the teaching jig is set properly on the position, or clean the teaching
jig.
60200e Auto. Teaching Mode in Auto.Opn
An error occurred during teaching. (Front) (Operation error in the Head Rotation
Center Offset Teaching)
Check that the teaching jig is set properly on the position, or clean the teaching
jig.
60200f Auto. Teaching Mode in Auto.Opn
An error occurred during teaching. (Rear) (Operation timeout in the Fiducial Mark
Position Teaching)
-----
602010 Auto. Teaching Mode in Auto.Opn
An error occurred during teaching. (Front) (Operation timeout in the Fiducial Mark
Position Teaching)
-----
602011 Auto. Teaching Mode in Auto.Opn
An error occurred during teaching. (Rear) (Operation error in the Fiducial Mark
Position Teaching)
Check that the teaching jig is set properly on the position, or clean the teaching
jig.
602012 Auto. Teaching Mode in Auto.Opn
An error occurred during teaching. (Front) (Operation error in the Fiducial Mark
Position Teaching)
Check that the teaching jig is set properly on the position, or clean the teaching
jig.
602013 Auto. Teaching Mode in Auto.Opn
An error for timeout occurred in the nozzle change. (Rear)
-----
602014 Auto. Teaching Mode in Auto.Opn
An error for timeout occurred in the nozzle change. (Front)
-----
602015 Auto. Teaching Mode in Auto.Opn
An error occurred in the nozzle change. (Rear)
-----
602016 Auto. Teaching Mode in Auto.Opn
An error occurred in the nozzle change. (Front)
-----
1005-001
6.14 自動教示