SOM-2079-001_w.pdf - 第172页
169 SOM-2079 装置情報コード 表示区分 A( 装置情報の概要 ) 表示区分 B( 装置情報の詳細 ) 801c0e Information The machine operation was stopped by a function of the P.C.B. counter stop mode. 801c0f Information Time-lag was detected in the process of the …
168
SOM-2079
装置情報コード 表示区分 A( 装置情報の概要 )
表示区分 B( 装置情報の詳細 )
801a06 Warning Operation
The status for the starting protection changed to ON.
801b01 Lightning Surge Warning
Lightning Surge Protector works; Q204.
801b02 Lightning Surge Warning
Lightning Surge Protector works; Q204. Running continue.
801c01 Information
This placement step was detected outside of the possible range. This step is auto
skip running.
801c02 Information
Feeder carriage has been paused to avoid clash with missing component. Please
collect component before operating the feeder carriage.
801c03 Information
Data was changed during machine worked. The changed data is not reflected in
operation until it stops or interrupts operation.
801c04 Information
PCB Origin Position data is not right. Please correct a PCB Origin Position on a
"Prod Chng(Origin Pos)" screen.
801c05 Information
Warm start mode was canceled.
801c06 Information
The machine stopped by the automatic stop function.
801c07 Information
Warm start mode was canceled. Please remove the unaccomplished PCB
801c08 Information
Started with abnormal feeder B offset data. Feeder B offset X and Y for 8mm tape
width, 2mm feed pitch component should be less than +/- 1.0mm.
801c09 Information
It started with the data out of the setting range contained in the placement level
d
a
ta of component supply changed data. On edit screen, the place level of square
shape below 3216 should be set up less than +0.5mm. When the place level
exceeding 0.5mm is required, please input H data of placement data (PP data).
801c0a Information
The number of times of flux reload reached the preset number of times. Please
confirm flux in a syringe is not insuffi
cient.
801c0b Information
The PCB product operation was cancelled on the way of the placement operation
by shortage of lot component. Open the safety cover and remove the PCB
directly.
801c0c Information
The Warm Start Mode on the stage1was canceled.
801c0d Information
The Warm Start Mode on the stage2 was canceled.
1005-001
6.19 装置情報
169
SOM-2079
装置情報コード 表示区分 A( 装置情報の概要 )
表示区分 B( 装置情報の詳細 )
801c0e Information
The machine operation was stopped by a function of the P.C.B. counter stop
mode.
801c0f Information
Time-lag was detected in the process of the operation window. The machine
operation will be stopped after inside P.C.B.'s are transferred to the out of the
machine. Please reboot the machine after stop of the machine operation.
801d01 Semi-auto(continue) start mode auto change
Production operation was interrupted for the state where PCB before component
are placed exists on XY table.
801e01 Placement Level Data
Calculated data out of range. Please check library data and pattern program data.
801f01 Warm start mode auto change
Operation was canceled for the state where the PCB in the middle of component
placing is on X/Y table.
802001 Alarm for Splicing
The feeder is running short of the component to feed. Please prepare for Splicing,
and remove the cover tape from the storage section.
802101 Feeder Maintenance Warning
The total number of feeder's shots reached a previous notice setting number.
802102 Feeder Maintenance Warning
The feeder adsorption rate decreased and exceeded the previous notice setting
number.
802201 ACV Information
Changing the feeder alternate condition to 'Disable' for ACV found empty feeder.
802202 ACV Information
C
h
anging the feeder alternate condition to 'Disable' for ACV found missing feeder.
802203 ACV Information
It faild in the Conv.Table and it failed in setting.
802301 Splicing No Check Alarm
The seam passed the detection sensor as unregistered splicing. Please register
the splicing.
803001 FAN Stop Warning
The ceiling cooling fan stopped.
803002 FAN Stop Warning
The lower mount (left fornt) cooling fan stopped.(M105)
803003 FAN Stop Warning
The lower mount (left rear) cooling fan stopped.(M106)
803004 FAN Stop Warning
The upper mount (left front) cooling fan stopped.(M107)
803005 FAN Stop Warning
The upper mount (left rear) cooling fan stopped.(M108)
803006 FAN Stop Warning
The lower mount side (left front) cooling fan stopped.(M109)
1005-001
6.19 装置情報
170
SOM-2079
装置情報コード 表示区分 A( 装置情報の概要 )
表示区分 B( 装置情報の詳細 )
803007 FAN Stop Warning
The lower mount side (left rear) cooling fan stopped.(M110)
803008 FAN Stop Warning
The CPU2 control box (left) cooling fan stopped.(M111)
803009 FAN Stop Warning
Fan stop detection satellite [STLT_FAN_MON] It does not answer. A fan stop is
normally undetectable.
80300a FAN Stop Warning
The conveyor multi-axis amplifi
er (left) cooling fan stopped.(M122)
80300b FAN Stop Warning
The lower mount side (right front) cooling fan stopped.(M116)
80300c FAN Stop Warning
The lower mount side (right rear) cooling fan stopped.(M117)
80300d FAN Stop Warning
The recognition BOX cooling fan stopped.(M118)
80300e FAN Stop Warning
The electrical system box power supply cooling fan (left) stopped.(M119)
80300f FAN Stop Warning
The electrical system box power supply cooling fan (right) stopped.(M120)
803010 FAN Stop Warning
The ceiling (left front) cooling fan stopped.(M102)
803011 FAN Stop Warning
The ceiling (left rear) cooling fan stopped.(M101)
803012 FAN Stop Warning
The ceiling (right front) cooling fan stopped.(M104)
803013 FAN Stop Warning
The ceiling (right rear) cooling fan stopped.(M103)
803014 FAN Stop Warning
The lower mount (right fornt) cooling fan stopped.(M112)
803015 FAN Stop Warning
The lower mount (right rear) cooling fan stopped.(M113)
803016 FAN Stop Warning
The upper mount (right front) cooling fan stopped.(M114)
803017 FAN Stop Warning
The upper mount (right rear) cooling fan stopped.(M115)
803018 FAN Stop Warning
The CPU2 control box (right) cooling fan stopped.(M118)
803019 FAN Stop Warning
The conveyor multi-axis amplifi
er (right) cooling fan stopped.(M124)
80301a FAN Stop Warning
The ceiling (rear) cooling fan stopped.(M101)
80301b FAN Stop Warning
The ceiling (front) cooling fan stopped.(M102)
1005-001
6.19 装置情報