200823.TR3000-IRV English Manual.pdf - 第19页

IR AUT O BGA R ework S tation TR3000-IRV Kukjetrading Co., Ltd. 19 the a ctual temperature would rise more than expected. This value is the maximum condition revealed by the device shipment test so it could be changed to…

IR AUTO BGA Rework Station TR3000-IRV

Kukjetrading Co., Ltd.

I. RS-232C : Communication Setting

(Caution!: This is for setting of communication conditions of a control board which directly controls an

industrial touchscren PC and equipments. Thus, it should not be changed arbitrarily.

II. Vision / Head : (Note: Currently this feature is not used.)

This part is for calibrating the vision of the device. It operates as follows.

A. Vision Calibration Key :

This key is used for calibrating the vision. When this key is touched, a head lowers down and picks

up parts and then, moves up, and a vision camera moves.

B. Vision Motor ◁ ▷Key :

This key is for moving a start point of a vision part right and left. When the center location of a part

tray is not correct, press this key to adjust the pick-up location.

C. Head Motor △▽ Key :

This key is for adjusting a location to be one on one for a head picking up of a part. When a head is

adjusted up and down, the image size of the BGA would change. Adjust the location to make the image

size to be the same as of a PCB pattern.

D. Camera Focus △▽ Key:

You can use this key for camera focus. But It can't move within auto focus.

E. Camera Zoom △▽ key:

It can adjust zoom for the camera. It use zoom or tele for Image

III. Compensation :

Since an infrared sensor is attached onto the TR3000IRV, the device gets controlled by the

temperature detected by the sensor. The detection area of the sensor is limited to the surface of a PCB

so the temperature detected by the sensor could be different from the temperature of the ball located on

the bottom of a BGA. A difference between the device setting and the actual value of a BGA ball could

be calibrated at this part. This value is expressed in a percentage. Thus, when a value is less than 100,

IR AUTO BGA Rework Station TR3000-IRV

Kukjetrading Co., Ltd.

the actual temperature would rise more than expected. This value is the maximum condition revealed

by the device shipment test so it could be changed to the actual value which has been measured.

♣ IR : It is for MODE 1~3 and it can be changed within a range of 70%~130%. (Standard 100%)

♣ TK : It is for compensating an error if there is an error in a value which is computed by measuring and

analyzing a temperature of a PCB. It can be changed within a range of 70%~130%. When this

value is low, the actual temperature is low as well.

♣ M4 : It is for MODE 4 and it can be changed within a range of 70%~130%. (Standard 100%)

♣ BOT : It is for Bottom heater and it can be changed within a range of 70%~130%. (Standard 100%)

♣ BTemp : It is temperature for PRE-HEAT (Standard 180degree)

IV. Set data Range :

It is possible to preset a range of analysis of data which appears when a DATA button is pressed. When the

maximum/minimum temperature range is present, time within such temperature range would be output. Value on

the left should be set to minimum and value on the right to maximum. For example, when the device gets operated

after entering a range 1: 150~180, it is possible to check the analysis time after completion of the operation.

5.2 About DATA

It is for measuring and analyzing the operation temperature and Save and Open it if necessary. It provides

the same function as the profiler.

IR AUTO BGA Rework Station TR3000-IRV

Kukjetrading Co., Ltd.

 When the data is touched, a range window appears on the right.

 It can analyze 4 ranges from the range 1 to 4 which are on the right of the screen. .

 Touch set keys next to the range 1 to 4 to click a triangle table for each of the range 1 and the range 2 to

set a temperature range to be analyzed.

 When an OK button is touched, elapse time for the corresponding zone is displayed in number next to

the PV and TK.

 With a save button or a delete button, it is possible to save or delete data onto the file.

5.2.1 Use DATA

① Adhere the end of a K-type wire sensor to a part to be worked with by using heat resistant tape and insert

a connector to a TK socket on the front of the device.

② After mounting a PCB onto a table, fasten it with screws which are used for fixing of space. During the

process, it becomes much easier if a board is fixed with a laminated-board fastening jig and a bottom

bending-prevention jig.

③ Press a center button to operate a vision camera.

④ Move a slide table to adjust the center of a vacuum bit to the center of a part. .

⑤ Check if a button of the heater 1 has been pressed. A large board should be selected by pressing up to the

heater 2.

⑥ Adjust the width of a splashback of an upper heater.

⑦ Press a RUN button to start heating.

⑧ The device operates in accordance with profile conditions and on the screen, PV values and TK values

are displayed in number and graphs are shown.

⑨ The operation is completed in accordance with the selected profile conditions and while a head elevates,

a cooling fan operates.

⑩ Press a “DATA” button, on the upper right of a screen, to select.

⑪ The initial temperature range is displayed on options. From the range 1~4, touch a set key to set a

temperature range to be changed and then, press OK. Then, elapse time within the preset temperature

range is displayed in a unit of second.