Board-Inverter-Operation-Manual-REV-F-2.pdf - 第10页
BI2000 Boa rd Invert er Manual Revision F / January 2022 Page 10 of 37 Te mperature and Hu midity 227B Operation and storag e s hould be d one at 4 0 – 105°F (4 – 41°C) and low h umidi ty. Do no t let condensa tion c oll…
BI2000 Board Inverter Manual
Revision F / January 2022
Page 9 of 37
Notices and Warnings
• 77BWear safety glasses, gloves, and long-sleeved clothing when working with
automated industrial equipment.
• 78BRead and understand all operating manuals before using this equipment.
• 79BDo not disable the safety features of the machine.
• 80BLock-out and tag-out the air and power supplies before any service is done.
• 81BReduce the air pressure to 0 psi before any hoses are removed.
• 82BMake sure all replacement parts are correctly rated for use.
• 83BAlways remain clear of all moving parts when the system is in operation.
Personal Protective Equipment
222BOperators must use eye protection because material contents are under pressure. Always
wear gloves when handling materials and solvents. Refer to MSDS sheets on the material
being dispensed for other precautions.
Environmental
Noise Levels
223BThe audible noise level of the board invertor is below 65 dBA.
Materials/Chemicals
224BThere are no dangerous materials or chemicals used in the operation of the machine.
Transportation, Operation, and Storage
Handling and Transportation
225BHandling and transportation should be done with minimal vibration and shock to the
system. An air-ride truck is recommended for roadway transport.
Storage
226BAll enclosures and connector covers should be closed tightly. The system should be
covered if dust or other airborne debris is present in the storage area.
BI2000 Board Inverter Manual
Revision F / January 2022
Page 10 of 37
Temperature and Humidity
227BOperation and storage should be done at 40–105°F (4–41°C) and low humidity. Do not let
condensation collect on the machine. Install the system on a level surface, away from
standing water, possible over spray, and overhead leaks.
Description of Components
228BThe PVA Board Inverter can process and invert multiple boards. It is SMEMA (Surface
Mount Equipment Manufacturers Association) rated for easy integration into a production
line. The unit is designed to operate with PVA workcells.
229BThe operator can control the system with the user interface. The machine status and error
messages are displayed on the LCD screen and the light tower (optional). Operators must
be trained or have read the manual.
230BAny uses other than listed above could result in a dangerous condition and cannot be
protected against by the safety features installed on the system.
231B
41BFigures 1 and 2: Functional Block Diagram and SMEMA Cables and Process Flow
Hazards Due to Contact
232BThe board invertor is designed to minimize injury from contact with the machine. In certain
modes of operation, you can enter the work area while the module is in operation. Only a
qualified person should do this. Examine warning labels.
BI2000 Board Inverter Manual
Revision F / January 2022
Page 11 of 37
Setup
WARNING: These procedures should be done by a qualified person in accordance with
this manual and applicable safety regulations. A “qualified person” is defined as “a
person or persons who, by possession of a recognized degree or certificate or
professional training, or who, by extensive knowledge, training, and experience, has
successfully demonstrated the ability to solve problems relating to the subject
matter and work.” (ref. ANSI/ASME B30.2-1983.)
Installation
1. 84BPlug the machine into an appropriate power source as shown by the Machine
Specific Information section of the Operating Guide or the legend plate on the
machine. The electrical service should be correctly grounded and the power source
“clean”. If there is high power equipment operating off the same source, a line
conditioner may be necessary. Machine errors can be caused by poor quality power.
WARNING: Failure to comply with electrical specifications can damage the machine
and injure personnel. Electrical hookup must be made by a qualified electrician and
comply with any local standards.
2.
85BConnect the ¼” NPT female fitting at the rear of the machine to a source of clean,
dry air. A hose of ¼” inside diameter is sufficient.
42BFigure 3: Main Air Attachment
3. 86BClose any access doors and engage the “Emergency Stop” button.
4.
87BTurn the red air lockout valve to “SUP”.
5.
88BMake sure any SMEMA cables are correctly connected.
6.
89BTurn the main power to switch “ON”.