Board-Inverter-Operation-Manual-REV-F-2.pdf - 第29页
BI2000 Boa rd Invert er Manual Revision F / January 2022 Page 29 of 37 Boa rd Thic kne ss Adjus tmen t 334B This pr ocedur e wil l adju st th e dist ance b etwe en th e chai ns, th ere sh oul d be a 1 mm gap betwee n the…
BI2000 Board Inverter Manual
Revision F / January 2022
Page 28 of 37
Maintenance
328B
Interval
329B
Action
330B
Weekly
•
167BClean the sensors with a lint-free damp cloth.
331B
Monthly
•
168BMake sure the conveyor belts are not worn.
• 169BApply grease to the chain.
•
170BCheck the pressure regulator for water and drain if
necessary.
•
171BMake sure the shock absorbers are tight and apply
grease.
Conveyor Belt Replacement
Note: Not all systems have conveyor belts, some have chains.
1.
172BLockout the power supply.
2.
173BRemove the old conveyor belt from the pulley wheels.
3.
174BInstall the belt on the pulley wheels farthest from the motor.
Note: Make sure there are no twists in the belt.
4.
175BInstall the belt around the large pulley wheel, then around the other wheels.
5.
176BRotate the pulley wheels several turns by hand to make sure the belt is correctly
seated.
Board Sensor Adjustment
332BUse a small screwdriver to turn the adjustment screw as necessary.
333B
64BFigure 25: Board Sensor Adjustment Screw
BI2000 Board Inverter Manual
Revision F / January 2022
Page 29 of 37
Board Thickness Adjustment
334BThis procedure will adjust the distance between the chains, there should be a 1mm gap
between the board and the chain. The gap between the upper and lower conveyor chain is
adjustable from 0.28” to 0.154” to reduce product movement during rotation. To adjust the
opening size, perform the procedure below.
Note: Make sure you know the current orientation of the roll cage so that you can
adjust the chain correctly.
Note: Adjust both sides of the conveyer evenly.
1.
177BEngage the Emergency Stop button.
2.
178BTurn the main air pressure to “Off”.
3.
179BLoosen the four shoulder bolts at the end of the turnbuckle. There are four bolts at
each end of the conveyor and each end is adjusted independently.
65BFigure 26: Loosen the Bolts Shown
4. 180BUse a ½” wrench to turn the turnbuckle.
66BFigure 27: Turnbuckle Adjustment
5. 181BWith the shoulder bolts loose, rotate the turnbuckle clockwise to increase the gap or
counterclockwise to reduce the gap.
BI2000 Board Inverter Manual
Revision F / January 2022
Page 30 of 37
6. 182BWhen the gap is correct, tighten the four shoulder bolts at the end of the turn
buckle.
7.
183BRepeat the procedure for the rear conveyor rail.
67BFigure 28: Conveyor Adjustment
Rotary Adjustment
Rotation Angle
338BThere are two shock absorbers that locate the roll cage. One shock is used at each position
(0 degrees and 180 degree); both shock absorbers are at the back of the machine.
1.
184BEngage the “Emergency Stop” button.
2.
185BTurn the main air pressure to “Off”.
3.
186BTo decrease the angle of rotation, turn shock absorbers clockwise. To increase the
angle of rotation, turn the shock absorbers counterclockwise.
4. 187BLock the shock absorbers with the hex locking nut after each adjustment.
68BFigure 29: Shock Absorber
5. 188BApply grease to the shock absorbers as necessary.