SIPLACE S-23 HM.pdf - 第268页

6 Vision functions User M anual SIPLACE S -23 HM 6.6 Test Component Software Version SR.406.xx 02/00 US Edition 268 The number of ba lls to be measured and the pattern tole rances defin e the size of the search win- dow …

100%1 / 454
User Manual SIPLACE S-23 HM 6 Vision functions
Software Version SR.406.xx 02/00 US Edition 6.6 Test Component
267
Rectangles: 6
dark blue: search window around the entire leads group or around every 6
light blue: search window around the first lead in a group 6
green: x and y tolerances 6
Cross: 6
white: Results of position recognition x and y angles 6
Overlay:
gray: Profile in the integration direction in question 6
blue: Gradients from the above profiles 6
The gradients are only required and displayed for the profiles in the
direction of the leads. 6
yellow: Results from the geometric filter 6
red: Interpolation limits for position determination 6
light blue: Results of interpolation -> Position 6
Comments: 6
An overlay is available for both directions of interpolation. 6
Optical measurement of BGAs and flip-chips with the 80F
4
or 80F
5
placement machine 6
The crosshairs indicate the position of the component in the camera coordinates system. The
outline of the component will be emphasized by the use of color. 6
The measured values represent geometric component parameters such as 6
– position in the camera coordinates system
– rotation angle
– maximum offset of the balls in x and y directions
– factor for the quality of measurement
6
1. Grid mode 6
See Section 6.6.4.14 on page 287 for a definition of the measuring methods. 6
Grid mode works with preset pattern tolerances and is therefore to be regarded as the first mea-
surement step in the optical surveying of BGAs and flip-chips. To ascertain the approximate posi-
tion it will be adequate to measure just a few connections. 6
6 Vision functions User Manual SIPLACE S-23 HM
6.6 Test Component Software Version SR.406.xx 02/00 US Edition
268
The number of balls to be measured and the pattern tolerances define the size of the search win-
dow. The rough position and the skew of the component are determined for each corner of the
component via a search window. This measurement method can be identified by 6
– the synthetic model being shown in pixel resolution at the lefthand edge of the video image,
and
– the 4 windows at the corners of the component.
Procedure: 6
– The algorithm defines 4 dark blue corner windows on the basis of the pattern tolerances and
the balls defined in the package form file. The default search value is 5 balls.
– A detection algorithm runs with the aim of detecting all balls corresponding to this type. Those
found will be marked with light blue crosses.
– The balls defined in the package form file are determined by the search algorithm. The balls
found are marked with a white outline. If defined balls are not found an error message will ap-
pear on the screen.
– From these data the rough position and the skew of the component are determined. The mea-
sured position of the component is marked with white crosshairs.
Rectangle: 6
dark blue: 4 search windows, depending on the pattern tolerances and
the number of balls 6
Cross: 6
white: Ball model candidates found 6
Overlays: 6
white: Balls found which are defined in the package form file 6
Crosshairs: 6
white: Results of position recognition -> x and y angles 6
Star: 6
white: Center of the component ->Position 6
Synthetic model representation at the lefthand edge of the video image: 6
Image: Model in pixel resolution 6
User Manual SIPLACE S-23 HM 6 Vision functions
Software Version SR.406.xx 02/00 US Edition 6.6 Test Component
269
Points marked with red plus signs (+): 6
outside the circle:
Contrast < 0, ball is darker than the background 6
within the circle:
Contrast > 0, ball is lighter than the background 6
Points marked with yellow minus signs (-): 6
The difference between the plus and minus signs represents
the radial tolerance. 6
2. Ball mode 6
See Section 6.6.4.14 on page 287 for a definition of the measuring methods. 6
The method works with high precision and is thus suitable for precisely determining the position
of all defined balls. As a higher precision search, ball mode will follow grid mode. 6
This measurement method can be identified 6
– by the synthetic model being shown in pixel resolution at the lefthand edge of the video image,
– by there being a window around every ball (separate window) or
Procedure: 6
All of the balls defined in the package form file are surveyed. Geometric criteria are used here in
the selection of the window mode: 6
– If the balls are relatively far apart the separate window mode will be selected. The default win-
dow mode is the separate window mode.
Window: 6
dark blue: Over a single ball in each case (separate window) 6
Over a row or over all balls (combined window) 6
Cross: 6
white: Measured ball candidates which are defined in the package form file. 6
Crosshairs: 6
white: Results of position recognition -> x and y angles 6
Star: 6
white: Position of the component 6