EdisonStandardOwnersManual-RevA-20170818B.pdf - 第142页
M AINTENANCE Edison Printer User Manual (Part Number 1023838) 142 Rev. A Copyright © 2017 ITW EAE All rights reserved. No part of the contents of thi s manual may be reproduced, copied or transmitted in any form or by an…
Edison Printer User Manual (Part Number 1023838) MAINTENANCE
Rev. A 141
Copyright © 2017 ITW EAE
All rights reserved. No part of the contents of this manual may be reproduced, copied or transmitted in any form or by any
means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage and
retrieval systems without the written permission of ITW EAE, unless for purchaser's personal use.
6.2.6. Verify Hood Lock Cylinder Functionality—Monthly
Figure 140. Hood lock adjustments.
Introduction
Verify hood lock cylinder functionality.
Estimated Completion Time
Less than 5 minutes
Procedure
Start from printer power ON.
Set in Initialize Controllers Only condition.
Close hood.
Observe icon at the top of the display change from a subdued state to a yellow open lock
state.
o Click on the icon to lock the hood.
o The lock icon should go green.
Attempt to open the hood manually by lifting and by vigorous shaking from left to right.
o If the hood can be opened, adjust the pneumatic cylinder on the left side (Figure 140).
o If the hood cannot be opened but the printer shuts down with a Hood State Changed
Unexpectedly fault, adjust the S1 safety switch.
MAINTENANCE Edison Printer User Manual (Part Number 1023838)
142 Rev. A
Copyright © 2017 ITW EAE
All rights reserved. No part of the contents of this manual may be reproduced, copied or transmitted in any form or by any
means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage and
retrieval systems without the written permission of ITW EAE, unless for purchaser's personal use.
6.2.7. Inspect and Clean the Anti-Static Brushes–Monthly
Figure 141. Inspect and clean Anti-static Brushes.
Introduction
Inspect and clean the Anti-Static Brushes on Transport belts front and rear.
Estimated Completion Time
Less than 5 minutes
Procedure
Start from printer power ON.
Set in Initialize Controllers Only condition.
Open hood.
Each transport belt has on anti-static brush.
o Brushes are mounted vertically near the belt drive motor system for each belt front
and rear (Figure 141).
o Brushes should be clean and flexible and free of solder paste contamination.
Examine the area beneath each brushes for belt debris.
o Belt debris may indicate potential belt wear.
Adjust or replace brushes as required
NOTE: Brushes need not be in contact with the belt to function properly. Brushes must be
within 1 mm of the belt.
Edison Printer User Manual (Part Number 1023838) MAINTENANCE
Rev. A 143
Copyright © 2017 ITW EAE
All rights reserved. No part of the contents of this manual may be reproduced, copied or transmitted in any form or by any
means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage and
retrieval systems without the written permission of ITW EAE, unless for purchaser's personal use.
6.2.8. Inspect Wiper Paper Shafts–Monthly
Figure 142. Inspect the drive shaft end for wear or damage.
Introduction
Inspect the wiper paper shafts for function of the toothed spurs and condition of the drive end.
Estimated Completion Time
Less than 5 minutes
Procedure
Remove the two shafts from the wiper assembly.
o Verify the toothed spurs (three per shaft) have freedom of movement and are not
clogged with paper.
o The toothed spurs are spring-loaded and should be able to return to position easily
Inspect the drive end to ensure for wear or damage would affect shaft performance (Figure
142).
Clean with a stiff brush and solvent as required.
NOTE: Take care when handling these assemblies to prevent injury, as the toothed spurs are
sharp.