3OM-1751-002w_G5S.pdf - 第103页

3OM-1751 1-49 1303-001 5.9 "Cmp Recog Pos" Window This window enables you to perform a teaching operation on the component recognition camera offsets (X (mm) Horizontal, Y (mm) Vertical, and Z (deg) Theta). [1]…

3OM-1751

1-481303-001

[Save] button

When this button is pressed, the teaching results are saved.

•

Glass Jig PCB JG-0166 (PEC Recognition Calibration Jig)

For the "PEC Recognition Camera & Beam Offset" teaching, the following

glass jig PCB is used.

Before the teaching operation, position and clamp the glass jig PCB on the PCB

positioning center.

Teaching Procedure

Procedure

(1) Select the Beam (1 or 2) for which the teaching is performed.

(2) Press the [Use] button in the "Glass Jig" section.

(3) Press the [Teach Start] button.

The designated beam (1 or 2) will move to the specied recognition mark

position and the following teaching operation will be performed.

•

PEC Recognition Camera Magnication X (Horizontal), Y (Vertical),

Z (Angle) Teaching (Camera 1 or 2)

•

Beam X (Horizontal) and Y (Vertical) Offset Teaching (Beam 1 or 2)

•

Beam Angle Z, Angle Y, Rectangular X Offset Teaching (Beam 1 or 2)

•

Pilot Pin Bending Position X Side, Angle (Beams 1 and 2)

•

When the teaching is performed, the start conditions are checked

and the head except for designated, is evacuated automatically.

•

When any recognition error occurs during the teaching operation or

the [STOP] button is pressed on the operation penal, the machine

is stopped temporarily. In this case, re-start is available.

•

During this temporary stop mode, the selection of any other menu

item is unavailable.

When the teaching is completed, the designated head returns to

the home position automatically.

The teaching results and mark recognition results during the

teaching (XY Angles) are displayed in the display area in the "PEC

Recognition Camera & Beam Offset" window.

5.8 "PCB Recog/Beam" Window

3OM-1751

1-491303-001

5.9 "Cmp Recog Pos" Window

This window enables you to perform a teaching operation on the component

recognition camera offsets (X (mm) Horizontal, Y (mm) Vertical, and Z (deg)

Theta).

[1]

[2]

F3A36

[1] Teaching Data Display Section

Displayed are the each offset data items for the designated camera and head.

[2] Teaching Procedure Display Area

Displayed are the buttons to be used for the teaching operations.

Select head

In this section, the buttons showing the component recognition cameras

corresponding to each head are displayed as images.

Select the component recognition camera for which the teaching is

performed.

[Noz. Place. Pos. move] Button

Using this button, the head is moved to the position where the nozzle to be

used for the teaching can be attached easily.

[Teach Start] button

When pressed, this button executes the teaching operation.

[Save] button

When this button is pressed, the teaching results are saved.

Graphic

Development

5.9 "Cmp Recog Pos" Window

3OM-1751

1-501303-001

•

Component Recognition Camera Offset Teaching Jig

For the component recognition camera offset teaching, the following jig is used.

Before the teaching operation, place the jig at its setup position and when the

teaching is completed, remove it.

QFP Glass Jig JG-0188 (KYB-M381P-00, Standard Equipment)

Notice

This jig is fragile, so take the greatest care to handle it.

12 mm

On the glass, the two patterns for the positional calculation are vapor-deposited.

QFP Glass Jig JG-0188 F3A37

•

Jig Pick-up Nozzle

For the pick-up of the QFP glass jig, the jig nozzle (standard equipment) or the

normal vacuum nozzle HV19C is used.

Before the teaching operation, change the nozzle in the "NOZ.CHNG." window

(Operation Sequence: Select [Unit Adj.] button in the Menus for Maintenance

→

Select [Noz Chng.] button).

5.9 "Cmp Recog Pos" Window