3OM-1751-002w_G5S.pdf - 第247页
3OM-1751 2-79 1303-001 [2] Dclr of backup axis Select the deceleration setting each for backup axis from the following items. Full Speed, 10% Decr, 20% Decr, 30% Decr, 40% Decr, 50% Decr, 60% Decr, 70% Decr, 80% Decr, 90…
3OM-1751
2-781303-001
[3] Cone Recog
Block 1, 2
Whether or not the corn recognition is performed automatically per head, is
set in this selection box.
AUTO
: When selected, the corn recognition is performed automatically.
Disable
: When selected, the corn recognition is not performed.
Note
(a) When the corn recognition function is used, the reference mark
recognition is not available.
(b) It is available when the high-speed head is used.
•
Set-up 3
[1]
[3]
[4]
[2]
[5]
[6]
[7]
F3B75
[1] Dclr of conveyor width's axis
Select the deceleration setting each for conveyor width axis from the
following items.
Full Speed, 10% Decr, 20% Decr, 30% Decr, 40% Decr,
50% Decr, 60% Decr, 70% Decr, 80% Decr, 90% Decr
Note
When the ambient temperature is lower than the specied temperature (20°C
± 10°C), perform the deceleration setting each for the conveyor width axis
and backup axis referring to the following setting standard.
•
Setting Standard based on Ambient Temperature
10°C or more : Full Speed
7 to 10°C : 50%
Less than 7°C : 70%
3.1 "Auto Ope. Set-up" Tab Sheet
3OM-1751
2-79
1303-001
[2] Dclr of backup axis
Select the deceleration setting each for backup axis from the following items.
Full Speed, 10% Decr, 20% Decr, 30% Decr, 40% Decr,
50% Decr, 60% Decr, 70% Decr, 80% Decr, 90% Decr
Note
When the ambient temperature is lower than the specied temperature (20°C
± 10°C), perform the deceleration setting each for the conveyor width axis
and backup axis referring to the following setting standard.
•
Setting Standard based on Ambient Temperature
10°C or more : Full Speed
7 to 10°C : 50%
Less than 7°C : 70%
Release [time]
When the set No. of backup axis operations is completed, the backup axis
deceleration setting is cancelled.
Set Value Range : 0 to 99
Replace [min]
When the set time period, standby time period and stop time period have
been elapsed, the deceleration control is performed again.
[3] Cover tape ll up Notice warning
Function
The cut tape debris amount is calculated based on the counted number
decided based on the component reload data (Tape feed, Feed pitch and
Type) on the component library data and the cut tape FULL alarm is issued
or machine stop operation is performed. Set "Enable" or "Disable" in this
selection box.
Check interval
The interval is selected from the following items.
Every 1000 mm
Every 500 mm
Every 300 mm
3.1 "Auto Ope. Set-up" Tab Sheet
3OM-1751
2-80
[4] Vibration control
Mode
The machine vibration is controlled by means of setting the deceleration in
the beam operation in the Y-direction.
Rate [%]
Set the vibration control rate in this data box.
Set Value Range: 1 to 99
[5] Trash box ll up Notice warning
For the Trash box ll-up notice warning, the following items are set.
Function
"Enable" or "Disable" is set in this selection box.
Notice [×1000]
Count : 1 to 9999 [×1000]
Initial value : 900 [×1000]
[6] Trash box ll up Stop warning
For the Trash box ll-up stop warning, the following items are set.
Function
"Enable" or "Disable" is set in this selection box.
Stop [×1000]
Count : 1 to 9999 [×1000]
Initial value : 1350 [×1000]
[7] Cmput box ll up Notice warning
The component discharge box full count is set in this data box.
1303-001
3.1 "Auto Ope. Set-up" Tab Sheet