3OM-1751-002w_G5S.pdf - 第96页
3OM-1751 1-42 1303-001 · T eaching Procedure Note Before performing the teaching operation, press the [ZERO] button in the "Control" menu to zero all axes. Procedure (1) Select the camera for which the teaching…
3OM-1751
1-411303-001
[Jig Detac Conrm.] button
When pressed, this button conrms the jig detachment.
[Save] button
When this button is pressed, the teaching results are saved.
[3] [Light Pt] button
The camera 1 or camera 2 lighting pattern is selected from the following
items.
ALL
: When selected, the teaching for the ring-lamp or coaxial lamp is
performed.
RING
: When selected, the teaching for the ring-lamp is performed.
COAX
: When selected, the teaching for the coaxial lamp is performed.
OPT
:
•
Teaching Jig for PEC Recognition Camera Lighting
The following jig components are used for the teaching on the PEC recognition
camera lighting. Before the teaching, combine the jig with the teaching glass jig
mounting support jig and place it on the PEC recognition camera.
After the teaching operation, remove it.
Teaching Glass Jig Mounting Support Jig
Teaching Glass Jig
(JG-0287,KYF-M8840-00)
(JG-0286,KYF-M8830-00)
F3A31
Notice
Set-up the teaching glass jig mounting support jig securely so that it does
not rise. If the mounting condition is not satisfactory, the head, etc., might
be damaged.
5.5 "PCB Recog Light" Window
3OM-1751
1-421303-001
·
Teaching Procedure
Note
Before performing the teaching operation, press the [ZERO] button in the
"Control" menu to zero all axes.
Procedure
(1) Select the camera for which the teaching is performed in the "Select Camera"
section.
(2) Select the block where the jib is setup in the "Select Jig" section.
(3) Press the [XY Beam Save Pos] button and within 10 seconds, press the
[START] button on the operation panel.
Note
The lock for the transparent cover is undone automatically.
(4) Open the transparent cover. Then, turn up the white side of the teaching
glass jig and set up the PEC recognition lighting teaching jig on the PEC
recognition camera.
(5) Press the [Jig Set Conf] button.
(6) Close the transparent cover and press the Cover Lock Switch ([Cover Ready]
button) on the main machine.
(The transparent cover will be locked).
(7) Press the [Teach Start] button.
(The PEC recognition camera will move onto the PEC recognition lighting
teaching jig to perform the teaching operation on lighting.)
(8) Press the [Beam Evac Move] button and within 10 seconds, press the [START]
button on the operation panel.
Note
The lock for the transparent cover is undone automatically.
(9) Open the transparent cover in the corresponding block.
(10) Remove the setup PEC recognition lighting teaching jig.
Notice
Unless the lighting teaching jigs are removed, the head would be
damaged.
(11) Close the transparent cover and press the Cover Lock Switch ([Cover Ready]
button).
(12) Press the [Jig Detac Conrm.] button.
(13) Press the [Save] button to save the teaching results.
5.5 "PCB Recog Light" Window
3OM-1751
1-431303-001
5.6 "MARK LIGHT" Window
[1]
[2]
F3A32
[1] Teaching Data Display Section
Displayed are the offset data items for each reference mark for the designated
camera.
[2] Teaching Procedure Display Area
Displayed are the buttons to be used for the teaching operations.
Select camera
Each PEC recognition camera in the graphic image of the machine is
provided with a button function. Select the camera in the block for which the
teaching operation is performed.
[Teach Start] button
When pressed, this button executes the teaching operation.
[Save] button
When this button is pressed, the teaching results are saved.
·
Teaching Procedure
Procedure
(1) Select the component recognition camera for which the teaching is
performed, in the "Select Camera" section.
(2) Press the [Teach Start] button.
(In a single teaching operation, the marks in the rear and front of the
designated component recognition camera are taught one by one).
(3) Press the [Save] button.
Graphic
Development
5.6 "MARK LIGHT" Window