3OM-1751-002w_G5S.pdf - 第80页
3OM-1751 1-26 4.3.1 "Conveyor" T ab Sheet [1] [2] [3] "Conveyor" Tab Sheet F3A20 [1] Conveyor Display Section The conveyor image is displayed in this section. [2] Control Switch These buttons are arra…
3OM-1751
1-251303-001
4.3 "CONVEYOR" Window
This button is used for the adjustment operation for the conveyor width overall
setup or manual setup.
[1]
"CONVEYOR" Window F3A19
[1] Tabs
The "CONVEYOR" Window is provided with the following two tabs.
When each tab is pressed, the corresponding tab sheet appears.
Tabs Description
Conveyor
When this tab is selected the tab sheet for the conveyor operation is displayed.
PCB Stpr.
When this tab is selected the tab sheet for the PCB stopper operation is
displayed.
T3A3
Graphic
Development
4.3 "CONVEYOR" Window
3OM-1751
1-26
4.3.1 "Conveyor" Tab Sheet
[1]
[2]
[3]
"Conveyor" Tab Sheet F3A20
[1] Conveyor Display Section
The conveyor image is displayed in this section.
[2] Control Switch
These buttons are arranged to perform the following setup operations. When
any button is selected the background color of the selected button turns
green.
[Desig Width] Button
When each value for "Tgt Wd", "Clearance" and "Base Pos" are set and
the [START] button on the operation panel is pressed within 10 minutes
after pressing this button, the target position movement is performed.
[Zeroing] Button
When the [START] button on the operation panel is pressed, within 10
seconds after pressing this button, the conveyor zeroing operation is
performed.
[PCB posn.lct.snsr.Tch] Button
When this button is pressed, the teaching operation for the PCB
positioning detection sensor is performed based on the current conveyor
width.
Note
When there is a PCB on the conveyor, accurate teaching is not
available. Make sure that there is no PCB on the conveyor and press
this button to perform the teaching operation.
1303-001
Graphic
Development
4.3 "CONVEYOR" Window
3OM-1751
1-271303-001
[3] Conveyor Setup Buttons
When the target position is to be moved the conveyor width adjustment
values are setup using the following buttons.
[Tgt Wd] Button
When this button is pressed the "Tgt Wd" input window appears. When a
value is entered and the [SET] button is pressed the target value is setup.
[Clearance] Button
When this button is pressed the "Clearance" input window appears.
Set the data for the conveyor width to have some margin from the PCB
size set in the pattern program. The actual conveyor width is "PCB Size"
(Target Width) + "Clearance" (Recommended Value: 0.5 mm).
When a value is entered and the [SET] button is pressed the clearance
value is setup.
[Base Pos] Button
When this button is pressed the "Base Pos" input window appears. In
this window the base position adjusting data is setup. When the value is
entered and the [SET] button is pressed, the base position is setup.
·
Conveyor Width Manual Setup
When the conveyor width is to be set up, use the following procedure.
Procedure
(1) In each input window displayed by pressing the [Tgt Wd], [Clearance] and
[Base Pos] buttons for the "Conveyor" width, enter the data parameter for
each item.
(2) Within 10 seconds after pressing the [Tgt Wd] button, press the [START]
button on the operation panel.
(The conveyor width will be adjusted to ("Tgt Wd" value + "Clearance"
value). Also, the conveyor will be moved to the set base position.)
4.3 "CONVEYOR" Window