JX-100_SPE_EN06.pdf - 第26页

6.4.3 ATF For splicing of component feed t ape (tape splicing), this t ape feeder permits a component feed during production. 1) Specifications ① 8mm T ape type Product code Paper Embossed Feeding pitch Number of pins at…

100%1 / 40
6.4.2 CTFR
1) List of specifications
Tape type
Product
code
Paper Embossed
Feeding pitch
Number of pins
at the edge
Diameter of a
reel
Typical component
type
CF03HPR
○ －
0603
CF05HPR
○ －
1005
CF08HER
－ ○
2mm
Two-terminal diode
CF081PR
○ －
1608, 2012, 3216
CF081ER
－ ○
Φ180mm
SOT
CF8L1PR
○ －
1608, 2012, 3216
CF8L1ER
－ ○
4mm
Two
Φ180 −
Φ380mm
SOT
CN05HPR
○ －
1005
CN08HER
－ ○
2mm
Two-terminal diode
CN081CR ○ ○
Φ180mm
1608, 2012, 3216
CN8L1CR ○ ○
4mm
One
Φ180 −
Φ380mm
1608, 2012, 3216
* For a tape feeder designed for both paper and embossed paper, contact our sales
person.
* Use a tape feeder whose supported component sizes and tape specifications conform to
the JIS C0806-3:1999 and IEC 60286-3:2007.
2) Common specifications
1
Power supply/air supply None
C*0***R L=602mm, H=208mm, W=16.2mm
2
Dimensions
C*8L1*R L=683mm, H=431mm, W=16.5mm
C*0***R 1.2kg (Excluding a reel)
3
Mass
C*8L1*R 1.9kg (Excluding a reel)
4
Component transport method Ratchet drive system
3) Options
① Bar code tag
This tag is used to paste a bar code mark onto the rear edge of a tape feeder.
Even after you install a tape feeder on the feeder bank, the pasted bar code can be
read easily.
② Tape reel mounting platform
This is a platform that allows you to set a tape onto a tape feeder. Since you can set
a tape while holding a tape feeder correctly, this option improves the tape setting
capability and prevents a tape feeder from falling down.
Type Application
Tape reel mounting platform
(no foot)
A user is supposed to fix this option onto a table or similar device
with screws.
Tape reel mounting platform
(with foot)
This option is equipped with foot, so you can install this option as
desired.
21
6.4.3 ATF
For splicing of component feed tape (tape splicing), this tape feeder permits a component
feed during production.
1) Specifications
① 8mm
Tape type
Product code
Paper Embossed
Feeding
pitch
Number of pins
at the edge
Diameter
of a reel
Typical component
type
AF05HP
○ －
1005
AF08HE － ○
2mm
Two-terminal diode
AF081P ○ － 1608, 2012, 3216
AF081E － ○
4mm
Two
SOT
AN05HP ○ － 1005
AN08HE － ○
2mm
Two-terminal diode
AN081P ○ － 1608, 2012, 3216
AN081E － ○
4mm
One
Φ180mm
SOT
* For a tape feeder designed for both paper and embossed paper, contact our sales person.
* Use a tape feeder whose supported component sizes and tape specifications conform to the
JIS C0806-3:1999 and IEC 60286-3:2007.
② 12mm to 24mm
Applicable component
Product code Feed pitch Pick position (Y direction)
Emboss width Emboss depth
AF121S 4mm
AF122S 8mm
AF123S 12mm
AF12FS 4/8/12mm
AF12NS 4/8/12mm
8.3 mm
or less
AF161S 4mm
AF162S 8mm
AF163S 12mm
AF16FS 4/8/12/16mm
AF16NS 4/8/12mm
12.2 mm or less
AF242S 8mm
AF243S 12mm
AF244S 16mm
AF245S 20mm
AF246S 24mm
AF24FS 8/12/16/20/24mm
AF24NS 8/12mm
132mm
AF24FS-OP 8/12/16/20/24mm 114 mm
20.2 mm or less
17mm or less
* Use a tape feeder whose supported component sizes and tape specifications conform to the
JIS C0806-3:1999 and IEC 60286-3:2007.
2) Common specifications
8mm 12mm/16mm 24mm
1 Power supply/air supply None
2 Dimensions
L=645mm
H=213mm
W=16.8mm
L=693mm
H=472mm
W=31.5mm
L=693mm
H=472mm
W=40mm
3 Mass (Excluding a reel) 1.8 kg or less 2.45kg or less 2.6kg or less
4 Component transport method Ratchet drive system
22
3) Options
① Bar code tag (8mm only)
This tag is used to paste a bar code mark onto the rear edge of a tape feeder.
Even after you install a tape feeder on the feeder bank, the pasted bar code can
be read easily.
② Embossed tape spacer
To improve the feed and pickup stability of the carrier tape for the emboss
component made of a soft and fragile material, this spacer is installed in the
emboss groove of the feeder to support the bottom surface of the carrier tape.
A type for 8 mm feeder, type for both 12 mm and 16 mm feeders, and type for 24
mm feeder are available.
③ Tape reel mounting platform
This is a platform that allows you to set a tape onto a tape feeder. Since you can
set a tape while holding a tape feeder correctly, this option improves the tape
setting capability and prevents a tape feeder from falling down.
Type Application
Tape reel mounting platform (no foot) A user is supposed to fix this option onto a table or similar
device with screws.
Tape reel mounting platform (with foot) This option is equipped with foot, so you can install this
option as desired.
④ Joint tape splicing jig (8mm only)
When you use a JUKI designated joint tape, this jig allows you to paste a joint
tape with glue easily.
⑤ Joint tape
This is a tape that splices an old tape reel and a new tape reel.
A dedicated type for each tape width is available.
⑥ Scissors (Tape cutting jig A, and B)
A positional adjustment between the tape feeder used during the production and
a new tape feeder to be connected can be accurately and quickly made by cutting
the tapes with dedicated scissors when they are spliced.
・Tape cutting jig A: Available for feed pitch (4, 12, 20, 28, 36, 44, 52).
・Tape cutting jig B: Available for feed pitch (8, 16, 24, 32, 40, 48, 56).
23