JX-100_SPE_EN06.pdf - 第28页

6.4.4 FTF/FTFR 1) Specification t able ① FTF (12 mm, 16 mm, 24 mm, and 72 mm) Applicable c omponent Product code Feed pitch Pick position (Y direction) Emboss wid th Emboss depth FF121S 4mm FF122S 8mm FF123S 12mm FF12FS …

100%1 / 40
3) Options
① Bar code tag (8mm only)
This tag is used to paste a bar code mark onto the rear edge of a tape feeder.
Even after you install a tape feeder on the feeder bank, the pasted bar code can
be read easily.
② Embossed tape spacer
To improve the feed and pickup stability of the carrier tape for the emboss
component made of a soft and fragile material, this spacer is installed in the
emboss groove of the feeder to support the bottom surface of the carrier tape.
A type for 8 mm feeder, type for both 12 mm and 16 mm feeders, and type for 24
mm feeder are available.
③ Tape reel mounting platform
This is a platform that allows you to set a tape onto a tape feeder. Since you can
set a tape while holding a tape feeder correctly, this option improves the tape
setting capability and prevents a tape feeder from falling down.
Type Application
Tape reel mounting platform (no foot) A user is supposed to fix this option onto a table or similar
device with screws.
Tape reel mounting platform (with foot) This option is equipped with foot, so you can install this
option as desired.
④ Joint tape splicing jig (8mm only)
When you use a JUKI designated joint tape, this jig allows you to paste a joint
tape with glue easily.
⑤ Joint tape
This is a tape that splices an old tape reel and a new tape reel.
A dedicated type for each tape width is available.
⑥ Scissors (Tape cutting jig A, and B)
A positional adjustment between the tape feeder used during the production and
a new tape feeder to be connected can be accurately and quickly made by cutting
the tapes with dedicated scissors when they are spliced.
・Tape cutting jig A: Available for feed pitch (4, 12, 20, 28, 36, 44, 52).
・Tape cutting jig B: Available for feed pitch (8, 16, 24, 32, 40, 48, 56).
23
6.4.4 FTF/FTFR
1) Specification table
① FTF (12 mm, 16 mm, 24 mm, and 72 mm)
Applicable component
Product code Feed pitch
Pick position
(Y direction)
Emboss
width
Emboss
depth
FF121S 4mm
FF122S 8mm
FF123S 12mm
FF12FS 4/8/12mm
FF12NS 4/8/12mm
8.3mm or
less
FF161S 4mm
FF162S 8mm
FF163S 12mm
FF16FS 4/8/12/16mm
FF16NS 4/8/12mm
12.2mm or
less
6.5mm or
less
FF242S 8mm
FF243S 12mm
FF244S 16mm
FF245S 20mm
FF246S 24mm
FF24FS 8/12/16/20/24mm
FF24NS 8/12mm
20.2mm or
less
FF724S 12/16mm
FF728S 12/16/20/24/28/32mm
132mm
62mm or
less
10.5mm or
less
Power supply/air None
FF12** L =693mm , H =472mm, W=31.5mm
FF16** L =693mm , H =472mm, W=31.5mm
FF24** L =693mm , H =472mm , W=40.0mm
Dimensions
FF72** L =693mm , H =472mm, W=89.2mm
Mass
(Excluding a reel)
FF12**: 2.45kg , FF16**: 2.45kg , FF24**: 2.6kg,
FF72**: 5.1kg
Component transport
method
Ratchet drive system
* Use a tape feeder whose supported component sizes and tape specifications conform to
the JIS C0806-3:1999 and IEC 60286-3:2007.
24
② FTFR (32 mm, 44 mm, and 56 mm)
Applicable Component
Product code Feed pitch
Pick position
(Y direction)
Emboss
width
Emboss
depth
FF323R 12mm
FF324R 16mm
FF32FR 8/12/16/20/24mm
132mm
FF32FR-OP 8/12/16/20/24/28/32mm 114mm
23.5mm or
less
FF443R 12mm
FF444R 16mm
FF44FR 8/12/16/20/24mm
128mm
FF44FR-OP 8/12/16/20/24/28/32/
36/40/44mm
114mm
33.8mm or
less
FF564R 12/16mm 128mm
FF568R 12/16/20/24/28/32mm 114mm
FF56FR 8/12/16/20/24mm 128mm
FF56FR-OP 8/12/16/20/24/28/32/
36/40/44/48/56mm
114mm
46.0mm or
less
25mm or less
Power supply/air None
Dimensions
L =693mm , H =472mm
W= FTFR32**:47.7mm , FTFR44**:61.6mm , FTFR56**:66.0mm
Mass
(Excluding a reel)
FTFR32**:3.2kg , FTFR44**:3.5kg , FTFR56**:3.8kg
Component
transport method
Ratchet drive system
* Use a tape feeder whose supported component sizes and tape specifications conform to
the JIS C0806-3:1999 and IEC 60286-3:2007.
2) Options
① Emboss spacer (FTFR only)
When the component width and length are large and the tape depth is small, the
posture stability at component pickup can be improved by placing the spacer at
the component pickup position of the tape feeder.
The usable emboss depth is 1.0 mm to 8.0 mm.
② Tape reel mounting platform
This is a platform that allows you to set a tape onto a tape feeder. Since you can
set a tape while holding a tape feeder correctly, this option improves the tape
setting capability and prevents a tape feeder from falling down.
Type Application
Tape reel mounting platform (no foot) A user is supposed to fix this option onto a table or similar
device with screws.
Tape reel mounting platform (with foot) This option is equipped with foot, so you can install this
option as desired.
25