00191174-01.pdf - 第83页

User’s Manual Test Program S ITEST 4 Mapping Software Version 10.xx Edition 03/98 4.1 Preparatory Steps for the Mapping Operation 4 - 7 NOTE On SIPL ACE 80S m achi nes it is good pr actice to select the Mapp. both gantri…

4 Mapping User’s Manual Test Program SITEST

4.1 Preparatory Steps for the Mapping Operation Software Version 10.xx Edition 03/98

4 - 6

4.1.2 RV-Mapping

NOTE

Prior to the performance of RV-mapping make sure that PCB mapping has already been carried out.

The SITEST program must not have been restarted following PCB mapping.

●

Carry out the preparatory steps as described in section 4.1.

Additional prerequisites are:

both gantries must be in the park position.

segment offset

and

PCB/component camera offset must already have been determined for both

gantries.

the calibration piece must be in the calibration piece pocket.

the calibration piece position must already have been determined.

on segment 1 of each revolver head a size 617 nozzle must be attached.

●

From the main menu select the

Mapping

option and press the RETURN key.

The "Mapping" menu is displayed on the screen.

●

Select the

RV-mapping

function and press the RETURN key.

The "RV-mapping" menu is displayed on the screen.

Overview of the Functions:

RV-mapping to perform the RV-mapping

Cont. RV-mapping to perform mapping in the continuous run mode until the continuous run is aborted

by pressing ESC

Display mapping data to display the mapping data determined

Mapping data ct. run to display the data determined in the continuous mapping run

Continue RV-mapping to continue mapping from the measuring point entered

Mapp. both gantries to perform the mapping run for both gantries of SIPLACE 80S

(MC-changeover is carried out automatically. The mapping run is first performed

for gantry 1, thereafter for gantry 2.)

●

From the "RV-mapping" menu select the

RV-mapping

function and press the RETURN key. The active

gantry performs the mapping run. The measured values are automatically stored after the completion of

this mapping run.

Mapping

Mapping mode

PCB-mapping

RV-mapping

IC-mapping

Read mapping file

RV-mapping

Cont. RV-mapping

Display mapping data

Mapping data ct. run

Continue RV-mapping

Mapp. both gantries

User’s Manual Test Program SITEST 4 Mapping

Software Version 10.xx Edition 03/98 4.1 Preparatory Steps for the Mapping Operation

4 - 7

NOTE

On SIPLACE 80S machines it is good practice to select the

Mapp. both gantries

function instead of the

RV-

mapping

function so that the mapping run is performed for both gantries without

having to switch from gantry

1 to gantry 2 (Select gantry). When the mapping run of gantry 1 is completed, gantry 1 is automatically moved

to the park position, and subsequently the mapping run for gantry 2 is performed.

●

Press the ESC key twice to return to the SITEST main menu.

NOTE

The procedure described below is only required if on a SIPLACE 80S the RV-mapping procedure is per-

formed by means of the

RV-mapping

function

rather than the

Mapp. both gantries

function.

CAUTION

∆

Move gantry 1 to the park position using the menu functions of the "Gantry positions" menu (see

section 3.5).

●

Select the

Select gantry

menu option and press the RETURN key.

The "Select gantry" menu opens.

●

Select the

gantry 2 active

menu option for gantry 2 and press the RETURN key.

●

Press the ESC key to return to the SITEST main menu.

●

From the main menu select the

Mapping

option and press the RETURN key.

The "Mapping" menu is displayed on the screen.

●

Select the

RV-mapping

function and press the RETURN key.

The "RV-mapping" menu is displayed on the screen.

●

From the "RV-mapping" menu select the

RV-mapping

function and press the RETURN key. The active

gantry performs the mapping run. The measured values are automatically stored after the completion of

this mapping run.

●

Press the ESC key twice to return to the SITEST main menu.

4 Mapping User’s Manual Test Program SITEST

4.1 Preparatory Steps for the Mapping Operation Software Version 10.xx Edition 03/98

4 - 8

4.1.3 IC-Mapping

NOTE

Prior to the performance of IC-mapping make sure that PCB mapping has already been carried out.

The SITEST program must not have been restarted following PCB mapping.

●

Carry out the preparatory steps as described in section 4.1.

Additional prerequisites are:

PCB/component camera offset must already have been determined.

The calibration piece must be in the calibration piece pocket.

The calibration piece position must already have been determined.

The IC-camera must be completely calibrated.

On the IC-head a size 416 or 417 nozzle must be attached.

●

From the main menu select the

Mapping

option and press the RETURN key.

The "Mapping" menu is displayed on the screen.

●

Select the

IC-mapping

function and press the RETURN key.

The "IC-mapping" menu is displayed on the screen.

Overview of the Functions:

IC-mapping to perform IC-mapping

Cont.IC-mapping to perform mapping in a continuous run until the continuous run is aborted by

pressing ESC

Display mapping data to display the mapping data determined

Mapping data ct. run to display the data determined in the continuous mapping run

Continue IC-mapping to continue mapping from the measuring point entered onwards

●

From the "IC-mapping" menu select the

IC-mapping

function and press the RETURN key. The gantry

performs the mapping run. The measured values are automatically stored after the completion of the

mapping run.

●

Press the ESC key twice to return to the SITEST main menu.

Mapping

Select conv. side

Mapping mode

PCB-mapping

RV-mapping

IC-mapping

Cont.IC-mapping

Display mapping data

Mapping data ct. run

Continue IC-mapping