00197454-01_AI_Portal_40mm_TwinVHF_SX12_de_en.pdf - 第110页
assembly Assembly Twin VHF 3.2.5 Fitting the HC Us and HCU Base Adapter 110 Reconfiguration Kit Twin VHF with Gantry Reconfiguration Ki t T w in V H F m i t P o r - TF SX12 hoses Twin VHF - 01 1013 ► Connect the discharg…
assembly
3.2.5 Fitting the HCUs and HCU Base Adapter Assembly Twin VHF
Reconfiguration Kit Twin VHF with Gantry Reconfiguration Kit Twin VHF mit Portal 109
3.2.5
3.2.5 Fitting the HCUs and HCU Base Adapter
Fitting the HCUs and HCU Base Adapter
► Fit the HCUs onto the base adapter and then fit the base adapter onto the gantry.
Please read section "4.1.3 Replacing the Head Adapter for the HCU and the HCU" [ ➙ 136] and the
relevant chapter in the service manual for your machine.
3.3
3.3 Assembly Twin VHF
Assembly Twin VHF
The Twin VHF is fitted to the gantry before the gantry is installed.
Assembly Twin VHF
The Twin VHF consists of 2 identical Twin segments, which are fitted at an angle of 180°.
Each module is fixed with 4 screws to the head plate and
is positioned with two pins.
► Lift the first Twin VHF module into position and fasten
this into place using a long Allen key. Use
4 M4x14 (1) screws.
► Repeat this step for the second Twin VHF module.
► Fit the camera screen (1). This is fastened into place
using two black screws (2).
NOTICE!
Only use these screws to fix the camera screen. This pre
-
vents reflection when measuring components with the
stationary camera.
NOTICE
Hose and cable guidance
When performing the following steps, pay attention to the correct running of hoses and cables.
Refer to the diagrams for guidance.
assembly
Assembly Twin VHF 3.2.5 Fitting the HCUs and HCU Base Adapter
110 Reconfiguration Kit Twin VHF with Gantry Reconfiguration Kit Twin VHF mit Por
-
TF SX12 hoses Twin VHF - 01 1013
► Connect the discharged air connections for the two modules to the silencer.
► Connect the two return units, vacuum generator and digital valves with the pneumatic distributor.
1 Pneumatic distributor 2 Connection digital valve
3 Hose to Pin Picker (Smart Pin Support op
-
tion)
4 Connection for return unit
5 Connection for exhaust tube 6 Silencer discharged air
7 Head boards
assembly
3.2.5 Fitting the HCUs and HCU Base Adapter Converting the Cover
Reconfiguration Kit Twin VHF with Gantry Reconfiguration Kit Twin VHF mit Portal 111
► Connect the head boards with the HCU head adapter, using 2 flat ribbon cables in each case.
See also
1.2 Preparatory Work... [ ➙ 76]
3.4
3.4 Converting the Cover
Converting the Cover
When using the WPC5/6 for high components, you need to convert the cover. The new cover has a re
-
cess for the WPC on the disk.
Proceed as follows:
CAUTION
No WPC
If no WPC is fitted, you will not be able to feed in components with a height of 40 mm.
The cover may not be converted if there is no WPC.
1. Cover.
2. Hinges on the cover (2x)
CAUTION!
You may need to enlist the help of a second person for
this job.
► Loosen the screws fastening the hinges at the top of
the cover. While doing this, hold the front section of
the cover tight.
► Remove the front section of the cover.
► Insert the new front section of the cover into the ma
-
chine and screw into place.
1. Danger of crushing label (2x)
2. Barcode adhesive label
► Attach the following adhesive labels to the new cover.
For their exact positions, refer to the old cover.