Infinity Generic Tooling.pdf - 第30页

INFINITY MACHI NE PROG RAMMI NG STAGE 6E - FORM FLEX TOOLING 1.56 User Manual ST AGE 6E - FORMFLEX TOOLING Setup Plate and Weight s Procedure W ARNING BOARD CLAMPS. EX TREME CARE MU ST BE EXERCISE D WHEN WORKING IN THE T…

100%1 / 52
INFINITY
MACHINE PROGRAMMING
STAGE 6D - MULTIFLEX TOOLING
User Manual 1.55
47. Select Continue (F1).
48. Select Auto Board (F1).
49. Remove the board from the rails.
50. Select Continue (F1).
51. Go to Stage 7.
Continue Cancel
Auto
Board
Manual
Board
Continue Head
INFINITY
MACHINE PROGRAMMING
STAGE 6E - FORMFLEX TOOLING
1.56 User Manual
STAGE 6E - FORMFLEX TOOLING
Setup Plate and Weights Procedure
WARNING
BOARD CLAMPS. EXTREME CARE MUST BE EXERCISED WHEN WORKING IN
THE TOOLING AREA OF THE MACHINE TO AVOID INJURY. THE FOILS ON THE
FRONT AND REAR BOARD CLAMPS ARE VERY SHARP.
CAUTION
BOARD CLAMPS.
Care must be taken to ensure that the board clamps are
not damaged when removing or replacing tooling.
NOTE
1. Ensure that Generic Tooling is set to Enabled in Set Prefs.
2. When using FormFlex, the print gap in the product file must be set to zero.
1. Select Change Tooling (F6). The print carriage moves to the front of the
printer.
The Change Tooling Parameters window is displayed:
NOTE
If the remote board stop is fitted the Board Stop X and Board Stop Y
parameters are replaced by Remote Board Stop X.
2. Setting up the board stop position is automatically done using the board
dimensions previously set in the product file. If they need adjustment to re-
position the board stop for any reason, ie any routing on the board edge or
a badly positioned image on the stencil, this can be done now. If adjustment
is necessary continue with Step 3. If adjustment is not necessary go to Step
8.
3. Select Adjust (F1).
4. Use the Next and Previous keys (F4 - F5) to highlight each parameter.
5. Use the Incr. and Decr. keys (F6 - F7), or the forward slash key (/) on the
Mode
Load
Data
Edit
Data
Setup
Squeegee
Change
Screen
Change
Tooling
Change
Language
Exit
Change Tooling Parameters
BOARD WIDTH
BOARD STOP X
BOARD STOP Y
UNDER CLEARANCE
216.0
125.0
142.6
19.0
mm
mm
mm
mm
Adjust
Raise
Head
Remove
Cleaner
Board
Stop
Full
Width
Load
Width
Generic
Toolin g
Exit
Save Next Previous Incr. Decr. Exit
INFINITY
MACHINE PROGRAMMING
STAGE 6E - FORMFLEX TOOLING
User Manual 1.57
keyboard, to change the parameter value.
6. Select Save (F2). The message ‘Saving fiducial data - Please wait Board
data file saved’ is displayed.
7. Select Exit (F8).
8. Select Generic Tooling (F7).
The following window and menu bar are displayed:
NOTE
If contaminated squeegees are fitted, these should be replaced at this point.
9. Select Continue (F1). The print carriage travels to the rear of the machine-
and the following message is displayed ‘Table at Home Height’.
10. Select Transprt Height (F3), the message ‘Table at Transport Height’ is
displayed.
11. Place a board at the input sensor of the upline conveyor.
12. Select Load (F1).
Save Next Previous Incr. Decr. Exit
Save Next Previous Incr. Decr. Exit
Save Next Previous Incr. Decr. Exit
Adjust
Raise
Head
Remove
Cleaner
Board
Stop
Full
Width
Load
Width
Generic
Tooling
Exit
Generic Tooling Warning
WARNING Paste may drip into the machine
Remove Squeegees NOW
Continue
Open
Cover
No
Continue
Open
Cover
No
Load
Transprt
Height
Board
Clamps
Change
Screen
Raise
Head
Exit
Load
Vision
Height
Home
Height
Board
Clamps
Change
Screen
Raise
Head
Exit