Infinity Generic Tooling.pdf - 第50页
INFINITY MACHI NE PROG RAMMI NG STAGE 6F - AU TOFLEX TOOL ING 1.76 User Manual and the foll owing message is display ed ‘T able at Home Height ’ . 19. Select T ransprt Height (F3). The message ‘T able at T ransport Heigh…
INFINITY
MACHINE PROGRAMMING
STAGE 6F - AUTOFLEX TOOLING
User Manual 1.75
11. Select Save (F2).
12. Select Exit (F8).
13. Select Exit (F8).
14. Select Exit (F8). The rail moves to the board width and the selected Autoflex
pins rise.
15. Select Setup (F6).
16. Select Change Tooling (F6).
17. Select Generic Tooling (F7).
The following window and menu bar is displayed:
NOTE
If contaminated squeegees are fitted, these should be replaced at this point.
18. Select Continue (F1). The print carriage travels to the rear of the machine
Change
Autoflex
Save Next Previous Incr. Decr. Exit
Change
Autoflex
Save Next Previous Incr. Decr. Exit
Adjust
Raise
Head
Remove
Cleaner
Board
Stop
Full
Width
Load
Width
Generic
Toolin g
Exit
Mode
Load
Data
Edit
Data
Setup
Squeegee
Change
Screen
Change
Toolin g
Change
Language
Exit
Run Head
Paste
Load
Clean
Screen
Adjust Setup Monitor Maint.
Mode
Load
Data
Edit
Data
Setup
Squeegee
Change
Screen
Change
Tooling
Change
Language
Exit
Adjust
Raise
Head
Remove
Cleaner
Board
Stop
Full
Width
Load
Width
Generic
Tooling
Exit
Generic Tooling Warning
WARNING Paste may drip into the machine
Remove Squeegees NOW
Continue
Open
Cover
Exit
INFINITY
MACHINE PROGRAMMING
STAGE 6F - AUTOFLEX TOOLING
1.76 User Manual
and the following message is displayed ‘Table at Home Height’.
19. Select Transprt Height (F3). The message ‘Table at Transport Height’ is
displayed.
20. Place a board on the input sensor of the upline conveyor of the machine.
21. Select Load (F1).
22. Select Auto Board (F1).
23. Select Vision Height (F3). The message ‘Table at Vision Height. Check
Tooling Clearance’ is displayed.
24. Select Contact Height (F3).
The following window and menu bar is displayed:
25. Select Continue (F1). The message ‘Table at Contact Height. Check
Tooling Clearance’ is displayed.
Continue
Open
Cover
Exit
Load
Transprt
Height
Board
Clamps
Change
Screen
Raise
Head
Exit
Load
Vision
Height
Home
Height
Board
Clamps
Change
Screen
Raise
Head
Exit
Auto
Board
Manual
Board
Exit
Unload
Vision
Height
Home
Height
Board
Clamps
Change
Screen
Raise
Head
Exit
Contact
Height
Trans pr t
Height
Change
Screen
Raise
Head
Exit
Contact Height Warning
WARNING Check for obstructions between
the Rails and the Screen
Continue
Open
Cover
Exit
Continue
Open
Cover
Exit
INFINITY
MACHINE PROGRAMMING
STAGE 6F - AUTOFLEX TOOLING
User Manual 1.77
26. Select Raise Head (F7).
27. Raise the printhead using two button control.
28. Fit the head prop.
29. Press Confirm (F1).
30. Check that the setup of the tooling is adequate for the board, adjust as
necessary.
31. Select Lower Head (F2).
32. Remove the head prop.
33. Select Confirm (F1).
34. Lower the printhead using two button control.
35. Close the front printhead cover.
36. Press the System button.
37. Select Exit (F8).
The following window and menu bar is displayed:
38. Select Continue (F1).
Vision
Height
Raise
Head
Exit
Confirm
Lower
Head
Lower
Head
Confirm Cancel
Vision
Height
Raise
Head
Exit
Leaving Generic Tooling
WARNING You are about to return
to the Setup Page
Clear all tooling setup
equipment before proceeding
Continue Cancel
Continue Cancel