SussPA300UserGuide.pdf - 第60页

SUSS / PA300 / User Manual / M10-121841-00 / February 2002 59 12 Warranty and Limitations In general, SUSS probe stations carry a one year warranty covering labor, material and workmanship. This warranty does vary howeve…

SUSS / PA300 / User Manual / M10-121841-00 / February 2002

By following the guidelines set out in this manual injuries to personnel can be

minimized and damage to the system and materials prevented.

4. Guidelines in User Information

Safety instructions can be found in the appropriate chapters of this manual.

Following these will help to minimize danger.

11.2 Electronics

11.2.1 Basic Design

The electrical equipment contains a separate control panel which is connected with a

line cord to 230V 1 phase AC. This control panel is protection class 1. The PA300

prober is supplied with a safety low voltage of <30V.It is connected via a earth wire to

the control panel. The EMO supply voltage is separate and fulfils the requirements of

a safety low voltage smaller than 30V AC. There are no special risks.

11.2.2 Guidelines for Electronics in the User Information

The accident prevention guidelines for electrical and operational facilities should be

taken into consideration. The user has to ensure that the electrical and operational

facilities are periodically tested.

11.3 Radiation

Standard configuration produces no special risks in terms of radiation.

For possible HF interference from outside guidelines are given, but the operation should

not be influenced.

11.4 Earthquake Safety

Earthquake protection for the PA300 consists of interlocking coupling between the

table and the prober.

11.5 Total Risk Evaluation

The chances of injury have been reduced as they are dependent on several events

occurring at the same time:

• Irresponsible behaviour of the operator

• Accidental motion in the danger area

SUSS / PA300 / User Manual / M10-121841-00 / February 2002

12 Warranty and Limitations

In general, SUSS probe stations carry a one year warranty covering labor, material

and workmanship. This warranty does vary however for different types of probers as

well as for different areas of the world. Please review the specific warranty terms

outlined in your quotation for particulars pertaining to your equipment or the SUSS

general delivery terms and conditions. Please also refer to the specific purchasing

contract.

12.1 Scope

This warranty is limited to:

1. Equipment unpacked and installed by a SUSS representative unless other

conditions are agreed to by both parties and are set forth in writing.

2. Equipment used and operated in accordance with the User’s Manual.

3. Regular maintenance of the probe station (please refer to the User Manual)is

assumed for guarantee claims.

This warranty excludes:

1. Damage during shipment. Claims must be presented as determined by local

practice and dealt with via the SUSS appointed carrier and his insurance company.

2. Any items that are subject to normal wear and tear during the operation of the

equipment, such as probe needles or rubber gaskets.

All implied warranties, including warranties of use and fitness for a particular purpose

are limited in duration to the length of this warranty, unless otherwise provided by state

law. The warranty for additional equipment installed on a SUSS probe station is the

same as the original deliverer warranty.

The liability of SUSS MicroTec Test Systems GmbH is limited to the repair or

replacement, at our option, of any defective product and shall in no event include

incidental or consequential commercial damages of any kind.

12.2 Who is Protected

This warranty is offered only to the original purchaser of the equipment and on the

premises of the original dispatchment. Movement of the equipment to another premises,

especially over country borders, will lead to the invalidity of the guarantee claims.

SUSS / PA300 / User Manual / M10-121841-00 / February 2002

12.3 How to Receive Warranty Service

Please call your local SUSS representative or regional office.

It is also possible to contact SUSS MicroTec Test Systems GmbH during the following

hours:

Monday - Thursday: 07:00 to 17:00 (middle European time)

Friday: 07:00 to 15:00 (middle European time)

Telephone: +49 (0)35240 73 220

Fax: +49 (0)35240 73 722

Email: service@sussdd.de

Or:

Japan: Asia:

Tel: [+81] 45 - 931 - 5600 Tel: [+66] 2 - 938 - 44 - 26/- 27

Fax: [+81] 45 - 931 - 5601 Fax: [+66] 2 - 512 - 5569

USA:

Tel: [+001] 802 - 244 - 5181

Fax: [+001] 802 - 244 - 5103

Please be prepared to give the following information:

1. Company name, address and telephone number.

2. Name and extension number of the person we should contact, in case we need

further information.

3. Model type of the probe station and serial number of the prober as well as a list

of any peripheral equipment which may be associated with the system and the

connections.

4. A brief description of the problem or fault.

5. Based upon the information which you have provided, the Customer Service

Representative will give you further instructions or, if necessary, arrange a visit

from a service engineer.

The SUSS office or SUSS representative who processed your original order or currently

handles your customer account can give you specific instruction on how to obtain

warranty service.