4OM-1054-002.pdf - 第229页

Error ID ltem Description 470501 Shortage Of Comp. Attach the new comp. And press [READY]. Then, press [ST ART] button to re-start. (Cause 1) The tape feeder is empty of components. (Remedy 1) Re-load the tape feeder wit…

100%1 / 337
Error ID ltem Description
470301 Comp. Missing(Recog.)
(Cause 1) The machine stopped running because the component recognition camera detected
the "Component Missing (Recognition)" error continuously.
Ref.: When "9" is set in the "2" text box of "Error process" in the component library
data, it means that a pick-up error occurred continuously 9 times on the same
feeder No.
(Remedy 1) Follow the steps below to reset the machine to the normal condition.
(1) Check "Step" and "Feeder No." where an error has occurred.
(2) Press the [RETURN] and [ALL] button (entitled "ZERO"). After that, check
the following items related to the pertinent feeder No.
• Check if some components are left in the tape feeder.
• Check if the cover tape is peeled off normally.
• Check if the tape feeder is installed correctly on the feeder carriage.
• Check if the tape feeder is loaded with correct components.
• Check if some components are left in the carrier tape.
If left, be sure to remove them to protect the cutter blades from being dam-
aged.
• Check if the vacuum nozzle is not clogged or proper vacuum pressure is
applied.
(3) After taking the required countermeasures, re-start the production.
470401 Comp. Recog. Error
(Cause 1) The machine stopped running because the component recognition camera detected
the "Component Recognition Error (Recognition)" error continuously.
Ref.: When "9" is set in the "2" text box of "Error process" in the component library
data, it means that a pick-up error occurred continuously 9 times on the same
feeder No.
(Remedy 1) Follow the steps below to reset the machine to the normal condition.
(1) Check "Step" and "Feeder No." where an error has occurred.
(2) Press the [RETURN] and [ALL] button (entitled "ZERO"). After that, check
the following items related to the pertinent feeder No.
• Check if the tape feeder is loaded with correct components.
• Check the selected components and the component library data.
If wrong parameters are set in the component library data, correct them.
(3) After taking the required countermeasures, re-start the production.
3.3 Error IDs and Remedial Procedures
0307-005 2-111 AGS01ETRP
Error ID ltem Description
470501 Shortage Of Comp. Attach the new comp. And press [READY]. Then, press
[START] button to re-start.
(Cause 1) The tape feeder is empty of components.
(Remedy 1) Re-load the tape feeder with components and press the [READY] button. Then,
re-start the operation.
470601 Group Chip Remove this component. Then, press [START] button to re-
start.
470602 Group Chip Detect the next lot mark in the reset chip.
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy
470701 Alternate Feeder Disable Enable alt. And press [READY] button. Then, press [START]
to re-start.
(Cause 1) A component shortage error has occurred on all tape feeders in the group being used
as an objective one for the feeder alternate mode.
(Remedy 1) Press the [RETURN] button to cancel the error display. After that, set "Enable
Exist" for the feeders in the "Alternate Fdr. Mode" group box of the "Alternate" tab
sheet. (Operation Sequence: "OPN. MODE" Window (Submenu) Æ "Alternate"
Tab Sheet)
3.3 Error IDs and Remedial Procedures
0307-006 2-112 AGS01ETRP
3.3 Error IDs and Remedial Procedures
Error ID ltem Description
470801 Comp. Thickness(Sensor)
(Cause 1) The machine stopped running because the linear measure detection sensor de-
tected the "Component Thickness Error (Sensor)" error continuously.
Ref.: When "9" is set in the "2" text box of "Error process" in the component library
data, it means that a pick-up error occurred continuously 9 times on the same
feeder No.
(Remedy 1) Follow the steps below to reset the machine to the normal condition.
(1) Check "Step" and "Feeder No." where an error has occurred.
(2) Press the [RETURN] and [ALL] button (entitled "ZERO"). After that, check
the following items related to the pertinent feeder No.
• Check if the tape feeder is loaded with correct components.
• Check the selected components and the component library data.
If wrong parameters are set in the component library data, correct them.
Note: Check the parameter set as component thickness check data in
the "CMPNT CARRIAGE DATA EDIT" window.
(3) After taking the required countermeasures, re-start the production.
470901 Cancel Recovery On
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
0307-006 2-113 AGS01ETRP