JX-300LED_SPE_EN01.pdf - 第11页

- 7 - 4.2 Facility Specifications 4.2.1 Supply facilities and environmental conditions JX-300LED V oltage Three-phase 200V , 220V , 240V , 380V , 400V , 415V AC ±10% ( See Note 1 ) Frequency 50/60Hz Power supply Rated ap…

- 6 -

4. Specifications

4.1 Basic Specifications

(1) Board specifications and supported languages

JX-300LED

Board

dimensions (mm)

When clamped once : 610 mm×360 mm

When clamped twice : 1,200 mm×360 mm

When clamped three times (Option) : 1,500 mm×360 mm

IN/OUT buffer (Option) :410 mm×360 mm

(See Note 1.)

Board transport

direction

Left to right or right to left

Board transport

reference

position

Front reference only

Board transport

height

900±20mm

Board transport

specifications

Number of

buffers

No buffers (See Note 1.)

Applicable component height SC（6mm）NC（12mm）

Component size

(when recognized with laser)

0603 (See Note 2.) to 33.5 mm

Speed at which a square chip LED

component is placed on a board

(according to the JUKI designated

component placement pattern)

SC（6mm） : 18,200 CPH

NC（12mm） : 17,300 CPH

Speed at which a chip component is

placed on a board

(Conforming to IPC9850)

SC（6mm） : 18,300 CPH

NC（12mm） : 17,400 CPH

Component placement accuracy

(when recognized with laser)

±50μm （±3σ）

Number of components that can be

placed

Up to 40 component types (converted to the number of

components fed with an 8-mm tape when the front bank is

used)

Supported languages English, Japanese and Chinese

EN specifications None

Note 1: The machine is not equipped with any buffer as a standard device. When you add the

IN/OUT buffer option to the machine, the machine uses three buffers.

Note 2: Required HMS device(option) When use 0603 component.

(2) Recognition devices and heads

Laser recognition : LNC60

(this allows six nozzles to place small/low-profile chips on a

board at high speed.)

- 7 -

4.2 Facility Specifications

4.2.1 Supply facilities and environmental conditions

JX-300LED

Voltage

Three-phase 200V, 220V, 240V, 380V, 400V, 415V AC ±10%

(See Note 1)

Frequency 50/60Hz

Power supply

Rated apparent

power

3.0 kVA

Air pressure 0.5±0.05 MPa dry air

No Vacuum pump 345L/min (ANR)

Air supply

Maximum air

consumption

(See Note 2)

With vacuum pump 50L/min (ANR)

Ambient temperature + 10 to + 35 °C

Placement accuracy

guarantee temperature

+ 20 to + 25 °C

Relative humidity 30 % to 80% RH (No condensation)

During operation

Altitude 1,000m or less

Ambient temperature - 15°C to + 70°C

Environment

requirements

During transportation

or storage

Relative humidity 20 % to 95% RH (No condensation)

Noise 80 dB (A) or less (See Note 3)

Note 1: No power supply cable at the primary side is attached thereto.

We make NO WARRANTIES against any accident of the primary side wiring caused by

short–circuit of the power cable and so on. Please use a 5.5-mm2 or more diameter of

power cable for each phase. (Note: the appropriate cross-section area of the cable varies

depending on the supplied power voltage and the length of the power cable.)

Table Applicable sectional areas of primary side power cable lengths

Primary-side power cable length(m)

Supply power

Less than 20m 30m 40m 50m

AC 200/220/240V 8 8 10 12

AC 380/400/415V

Applicable

sectional area

(mm

)

8 8 8 8

Peak current (at AC200V 3phase power) : 35A

Note 2: “ANR” indicates are as follows:

Temperature = 20

C, Absolute pressure = 0.1MPa (=100kPa=1bar) and

Relative humidity = 65%

The necessary air supply shall be calculated as follows:

In case of 345 L/min (ANR), 345/0.926 (Coefficient) = 372.6 L/min: 372.6 L/min or more air

supply is required.

Note 3: This value was measured with conforming to the JIS Z8731 regulation.

- 8 -

4.2.2 Outside dimensions (except for the largest projections)

JX-300LED

(Unit: mm)

Size Standard

When a longer-sized board

(X-dimension: 1,500 mm) is

supported

Conveyor

height

900 only 900 only

A 1,920 2,520

B 210 510

C 1,710 *1

－

1,500 *2

*1 When a board is transported, the conveyor extension “B” on one side (IN side) is to be

removed from the standard machine according to the board transport specification.

*2 When a longer-sized board support option is attached on the machine, the conveyor

extensions “B” on both sides are to be removed from the machine.

4.2.3 Mass of the main unit

Standard machine: 1,420 kg

D (1,500 mm: length of the conveyor equipped with an option

when a board is transported)

265

1393

C (Length of the LR specification conveyor when a board is transported)

C (Length of the RL specification conveyor when a board is transported)

1685

1,300 (Width of the main unit)

000

1440

900