JX-300LED_SPE_EN01.pdf - 第15页

- 1 1 - 4.5 Applicable Components 4.5.1 Applicable component sizes Laser recognition (LNC60) Component size (Length × Width) Minimum: 0.6 × 0.3mm Maximum:  33.5mm (33.5mm on a side) Component height SC specification: 0.…

- 10 -

4.4 Nozzles

Various types of nozzles have been designed to increase the reliability of placement of

each type of components as shown in the table below.

For a standard nozzle to be attached on the JX-300LED, select it from among the nozzles

shown in the table below.

Table Nozzles supplied as the standard devices

Nozzle Nozzle assembly

Applicable components

(reference) and remarks

NO.

Internal

diameter

of a nozzle

External

diameter

of a nozzle

A B D E F G H

Std.

Nozzle

select

500 2-φ0.4 1.0 x 0.5 − 6 − − − − −

1005, 1608, 2012

See Note2

SOT (Molding: 1.6 x 0.8)

501 φ0.25 0.7 x 0.4 − − 6 − − −

0603

502 φ0.4 φ0.7 6 − 6 3 − − 3

1005

503 φ0.6 φ1.0 6 − 3 6 3 6 3

1608, 2012, SOT (Molding:

1.6 x 0.8), SOT (Molding:

2.0 x 1.25)

504 φ1.0 φ1.5 − 4 1 3 6 6 3

2012, 3216, SOT23, SOT

(Molding: 2.0 x 1.25)

505 φ1.7 φ3.5 1 2 − 3 3 1 3

Aluminum electrolytic

capacitor

(small), tantalum electrolytic

capacitor, trimmer

506 φ3.2 φ5.0 1 1 − 1 3 1 3

Aluminum electrolytic

capacitor (medium),

SOP (narrow type),

SOJ, Connector

507 φ5.0 φ8.5 1 1 − − 1 1 1

Aluminum electrolytic

capacitor (large),

SOP (wide type),

TSOP, QFP, PLCC,

Connector

508C φ8.0 φ9.5 1 1 1 1 1 1 1

See

Note1

QFP, PLCC, BGA

Total number of nozzles 16 15 17 17 17 16 17 15

* Total number of nozzles that can be installed onto an ATC station: 26 pieces.

Note 1: As a Std. Nozzle Select, you can select 15 nozzles among those whose number is from

500 to 508C.

However, you have to select a nozzle to be used for calibration of the machine:

- For laser calibration (one of the nozzles choose from 500, 502 and 503)

- For calibration (508C nozzle)

Note 2: Since a theta error may occur due to the shape of the surface of a 2012R component to

be picked, use a No. 504 nozzle if you have to place 2012R components in the high

density (the gap between the adjacent components: 0.3 mm or less).

- 11 -

4.5 Applicable Components

4.5.1 Applicable component sizes

Laser recognition (LNC60)

Component size

(Length × Width)

Minimum: 0.6 × 0.3mm

Maximum: 33.5mm

(33.5mm on a side)

Component height

SC specification: 0.09 mm (for a 0603 component) to 6.0 mm

NC specification: 0.09 mm (for a 0603 component) to 12.0 mm

Lead pitch 0.65mm or more

Ball pitch 1.0mm ～ 1.27mm

Note 1: The maximum size of components that can be recognized with 6 nozzles of the LNC60

at the same time is □ 10.0 mm.

When you are to place components whose size is more than □ 10.0 mm with the

LNC60 head, only three heads are used to pick them up.

Note 2: The described maximum dimensions of a component are applicable if a pick-up error of

the XY dimensions is ± 1 mm or less and the angle error is ± 3

or less.

Note 3: Components

☐

20 mm to

☐

33.5 mm can be used with the L3 or L4 head only.

Note 4: Components whose dimensions are 26.5 mm

11.0 mm are available even

4.6 Component Placement Accuracy at X, Y and

- The regulated value of a component to be recognized with laser is “Cpk ≧ 1.”

- The accuracy shall be the absolute value from the component reference mark or PWB

reference mark.

Component type XY

Square chip (0603) ±3°

Square chip (1005) ±2.5°

Square chip(1608 or larger)

±50μm

±2°

Square chip (LED) ±50μm ±3°

SOT ±0.15mm ±3°

Aluminum electrolytic capacitor ±0.3mm ±10°

Adjacent pitch

- 0603: 0.20mm

- 12 -

4.7 Applicable PWBs

4.7.1 PWBs transport direction

Rightward flow (transporting from left to right, viewed from the front side)

Leftward flow (transporting from right to left, viewed from the front side)

Note: This direction is determined at the factory.

4.7.2 PWB specifications

(1) PWB sizes (Unit: mm)

Maximum size(L2 x W2)

Minimum

size

(L1 x W1)

Clamped

once

Clamped

twice

Clamped three

times

Thickness

Standard

specification

610×360 1,200×360 -

Longer-sized

board (Option)

50×50

610×360 1,200×360 1,500×360

1.0 to 4.0

(actual

dimension)

Note: When “IN/OUT buffer (Option)” is used with 3 buffer operating, a borad size is able to

use up to

410×360mm.

(2) Maximum allowance of PWB mass

3,000g

(3) Allowable warpage of a PWB

0.2 mm or less per 50 mm area, and 1 mm or less for both upper and lower directions

(these values conform to the JIS B 8461 regulation.)

(4) PWB detecting sensor

A low reflectance PWB may not be detected by a sensor, independent of materials

and colors of the PWB.