JX-300LED_SPE_EN01.pdf - 第7页
- 3 - 3. System Configuration 3.1 JX-300LED System Configuration ○ : Equipped as standard ● : Option - : No setting Machine style JX-300LED Remarks Basic configuration Head unit ○ Laser recognition head( LNC60) ○ Offset …
- 2 -
③ Simultaneous Component Pick-Up Priority mode allows you to restrict the productivity
decrease caused by a simultaneous pick-up failure to the minimum.
④ The HMS (Option) allows you to check the component pick-up height and to perform a
teaching operation easily to prevent the operation rate from being lowered by a
component pick-up error.
Low Frequency of Failure Occurrence
① Since the laser unit continues monitoring the component pick-up condition until just
before a component is placed on a board, it allows you to check whether a component
drops or not.
② The function of self-calibrating the timing of releasing the vacuum pressure prevents
the components at a placement moment from being brought back.
③ Use of a vacuum pump greatly improves the stability of air supply available when the
machine picks up a component. (Option)
Versatility
① A bad mark indicating a defective circuit can be detected with an offset correction
camera (OCC).
② An LNC60 head can recognize up to 33.5 mm component with laser.
High Flexibility
① Program data created with a conventional CX or KE-series Machine can be loaded to
the machine.
② The machine performs idle board transportation even though the servomotors of the
heads or those of the X-Y axes are put in the free state.
Operability
① Displaying the graphics in rich facilitated an ease of operating the data inputs
② Key operations can be made easier by using a touch panel. (Option)
③ Provided with an option of feeder position indicator (FPI), the stocked components run
out or warns that the number of the remaining components is below the regulated
number with lighting the corresponding LED. This feature indicates which feeder is to
be replaced. (Option)
④ As a displayed language, English, Japanese and Chinese are supported depending on
the destination country.
⑤ Attachment of a USB port allows this mounter to use an external USB device. The
program can be shifted and backed up to an external recording unit.
High Serviceability
① The serviceability has been enhanced by displaying the screens of absorption
frequencies per nozzle and of X/Y axis traveling distances to call a checking time, in
addition to the hour meter (energized hours).
② Protecting the passwords has hierarchically stratified the maintenance levels to
increase a degree of freedom in setting the machine.
③ For the troubleshooting by operators, the HELP functions were fulfilled.
④ A head filter being a consumable part is installed in the upper part of the head to
facilitate replacement.
- 3 -
3. System Configuration
3.1 JX-300LED System Configuration
○: Equipped as standard ●: Option - : No setting
Machine style JX-300LED
Remarks
Basic configuration
Head unit
○
Laser recognition head(LNC60)
○
Offset collection camera L(OCC L)
○
Height measuring unit(HMS）
●*1
Bad mark reader(BMR)
●*1
Placement Monitor －
Power supply unit
○
Emergency stop button
○
Uninterruptible Power-supply System (UPS)
●*1
Electrical leakage breaker
●*1
I/O control unit
○
Motor control unit
○
X-Y control unit
○
Interior/exterior finish and equipment
○
Signal light (with buzzer)
○
Super foot
●*1
Caster
●*1
Pneumatic device piping system
○
Air regulator
○
Vacuum pump
●*1
Main line filter
●*1/○*2
Air coupler (Piping joint)
●*1
PWB conveyor unit
○
Board transport reference
○
Front reference
○
Rear reference －
Conveyor height 900 mm
○
Conveyor height 950 mm －
IN/OUT buffer (3 buffers)
●*1
For a board size up to 410 mm
in X axis
Placement station
○
Shape reference
○
Pin reference －
Support table unit
●*1
Including 16 support pins
Auto PWB width adjustment unit
●*1
Standard X-direction board size:
○
Up to 1,200mm in X-axis
Longer-sized board in X-axis
●*1
Up to 1,500mm in X-axis
Lighting unit of solder recognition
●*1
Component quantity control
●
- 4 -
Machine style JX-300LED
Remarks
Operation system
○
Liquid crystal display (with touch panel)
○
Touch panel ●*1
Keyboard, track ball ○
SSD ○
LAN port Ethernet ○
USB port ○
Rear-side operation unit
-
HOD ●*1
DVD/CD-ROM drive(USB) ●
FD drive(USB） ●
Equipment device
Feeder float sensor ○ Front side only
Automatic tool change unit(ATC) ○
Large-shape component scrap box －
Flexible calibration system(FCS） ○
FCS adjustment jig ●
Feeder position indicator(FPI) ●*1 Front side only
Component verification(CVS) －
Coplanarity －
Simplified load control －
Solder print recognition placement position correction －
Production support system
Flexline DB ○
External programming unti(EPU) ●
Flexline CAD ●
Host Line Computer (HLC) －
・IS －
Floor productivity improvement
・IFS-NX －
White list type anti-virus software ○
Feeder bank (Mechanical type)
Mechanical feeder bank (fixed type, Not on the rear side) ○
Mechanical feeder bank (trolley type) －
Trolley for mechanical feeder －
Intelli trolley(RFID) for mechanical feeder －
Connector bracket －
IC collection belt unit －
Component supply unit
-Tape feeder/bulk feeder ●
-Stick feeder ●
-Stacked stick feeder －