JX-300LED_SPE_EN01.pdf - 第16页

- 12 - 4.7 Applicable PWBs 4.7.1 PWBs transport direction Rightward flow (transporting from left to right, viewed from the front side) Leftward flow (transporting from right to lef t, viewed from the front side) Note: Th…

- 11 -

4.5 Applicable Components

4.5.1 Applicable component sizes

Laser recognition (LNC60)

Component size

(Length × Width)

Minimum: 0.6 × 0.3mm

Maximum: 33.5mm

(33.5mm on a side)

Component height

SC specification: 0.09 mm (for a 0603 component) to 6.0 mm

NC specification: 0.09 mm (for a 0603 component) to 12.0 mm

Lead pitch 0.65mm or more

Ball pitch 1.0mm ～ 1.27mm

Note 1: The maximum size of components that can be recognized with 6 nozzles of the LNC60

at the same time is □ 10.0 mm.

When you are to place components whose size is more than □ 10.0 mm with the

LNC60 head, only three heads are used to pick them up.

Note 2: The described maximum dimensions of a component are applicable if a pick-up error of

the XY dimensions is ± 1 mm or less and the angle error is ± 3

or less.

Note 3: Components

☐

20 mm to

☐

33.5 mm can be used with the L3 or L4 head only.

Note 4: Components whose dimensions are 26.5 mm

11.0 mm are available even

4.6 Component Placement Accuracy at X, Y and

- The regulated value of a component to be recognized with laser is “Cpk ≧ 1.”

- The accuracy shall be the absolute value from the component reference mark or PWB

reference mark.

Component type XY

Square chip (0603) ±3°

Square chip (1005) ±2.5°

Square chip(1608 or larger)

±50μm

±2°

Square chip (LED) ±50μm ±3°

SOT ±0.15mm ±3°

Aluminum electrolytic capacitor ±0.3mm ±10°

Adjacent pitch

- 0603: 0.20mm

- 12 -

4.7 Applicable PWBs

4.7.1 PWBs transport direction

Rightward flow (transporting from left to right, viewed from the front side)

Leftward flow (transporting from right to left, viewed from the front side)

Note: This direction is determined at the factory.

4.7.2 PWB specifications

(1) PWB sizes (Unit: mm)

Maximum size(L2 x W2)

Minimum

size

(L1 x W1)

Clamped

once

Clamped

twice

Clamped three

times

Thickness

Standard

specification

610×360 1,200×360 -

Longer-sized

board (Option)

50×50

610×360 1,200×360 1,500×360

1.0 to 4.0

(actual

dimension)

Note: When “IN/OUT buffer (Option)” is used with 3 buffer operating, a borad size is able to

use up to

410×360mm.

(2) Maximum allowance of PWB mass

3,000g

(3) Allowable warpage of a PWB

0.2 mm or less per 50 mm area, and 1 mm or less for both upper and lower directions

(these values conform to the JIS B 8461 regulation.)

(4) PWB detecting sensor

A low reflectance PWB may not be detected by a sensor, independent of materials

and colors of the PWB.

- 13 -

網掛け部ｻﾎﾟｰﾄﾋﾟﾝ設置不可範囲

4.7.3 Unavailable area for placing components on a board

Topside of a board

Figure Area on which no component can be placed

4.7.4 Unavailable area for setting a support pin

Bottom side of a board

Note 1: When the board transport direction is opposite (from right to left), the area in which no support

pin (Option) can be set is bilaterally symmetrical to that in the figure above.

Figure Area in which no support pin can be set

Stopper setting position

Shaded area: any support pin cannot be set.

Conveyor rail fixed (reference)side

(movable)

Board trans

ort direction

Board trans

ort direction

Area in which no component can be placed

Conveyor rail fixed side